As some additional insight into the care needed when working with some of
the most popular USB interfaces.
I have recently been working on understanding the lack of sensitivity in a
900 MHz ISM device. This device is controlled by an FTDI245RQ USB interface.
The clock for this device can be an
For Sale: RemoteRig 1258 MkII set with wifi added + Cables and RRC Micro
Client. Like new condition used very little total cost was $909.75 from
Elecraft and HRO Asking $720. Will break out parts if there is interest.
If interested please contact me directly, off the reflector.
73
Brian
Bill
The station has a bank of 4 marine batteries and a 1 kw inverter backing up
the K3s, kat500, Steppir controller, Green heron rotor and the computer.
Power outages are a regular occurrence at this remote location in Upstate
New York, However; the first thing that would happen in this case
Expanding my problem a little more. I have a remote that uses a KAT500 that
is now 3000 miles away. The KAT500 was calibrated to use the correct antenna
over all bands 160 to 6 meters at the specified increments (10 KHz 160 etc
and 20 KHz for the higher bands) For an unknown reason the KAT 500 has
Can I change the KAT500 ant selection from the K3s
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by:
I am not close to my set up now so I cannot send a picture.
>That first picture reflects one thing I hate about my KX3 and PX3 - when
you have
>everything hooked up, it is one mass of wires everywhere.
>The KX3 and PX3 is a fantastic pair in every other way, but dang, I can?t
handle
>the
I am sure the extra cost for building and testing any of the Elecraft
products is worth the money if that is the way someone wants to go. All the
Elecraft products I have, or have had, were built by my son Andrew KK6EME
that includes 2 K3s, P3, KX3, KPA500, KXPA100 and a K2 /100(sold). The only
.
Thanks
Brian KF6C
-Original Message-
From: Nr4c [mailto:n...@widomaker.com]
Sent: Saturday, December 12, 2015 5:50 PM
To: Brian D. Comer
Subject: Re: [Elecraft] K30-Mini link stoped working.
IP addresses?
Sent from my iPhone
...nr4c. bill
> On Dec 12, 2015, at 8:26 PM, Brian D. Co
I am in the process of setting up a remote station. I have the K30-mini and
the two RRC1258 units with a K3S as the remote.
Currently I am on using my LAN, which worked fine on initial setup. In
trying to set up the remote using HRD and the control RRC, I have broken the
system. In returning
I think stating any particular antenna configuration is unacceptable is
ignoring what could be an ideal antenna for a given situation. As I
understand it a rhombic uses a resistor, and sometimes works quite well.
On 160 I have an OCFD 1/2 wavelength that is goes from one side of the end
of a
Please ignore this message, at some time windows 10 did install the drivers.
73 Brian KF6C.
From: Brian D. Comer [mailto:br...@kf6c.com]
Sent: Thursday, December 10, 2015 9:21 AM
To: 'elecraft@mailman.qth.net'
Subject: K3/0-MINI and windows 10
Does anyone have any experience
Does anyone have any experience installing the FTDI drivers on windows 10
for the K3/0 mini. Windows 10 does not appear to install them automatically.
I cannot find instructions on the web site.
Thanks 73
Brian KF6C.
__
I did not calibrate my K3s smeter on initial assembly, nor have I done it
since, so the following is as per factory setup with no atten or preamp,
AGC-F, RFgain Max. The radio has KFL3B-FM, KFL3A-6K, KFL3A-2.8K,
KFL3A-400, and KBPF3A installed.
Injection of a 50uV signal (50 ohms) (-73dBm)
I have noted a similar Cracking in the speaker when listing to AM broadcast
station KFI (640 KHz). At first I assumed it was just overload as I was
using a 160 meter dipole and the signal strength meter was maxed: however
moving to steppir antenna tuned to 40 meters gave the same result with
I think if I chucked the power supply for my TCS12 TX and RX, the K3 and the
KX3 in the lake they would all end up at the bottom maybe take different
times to get there but I can't see any of them floating!
73
Brian KF6C.
-Original Message
Ohhh, and they need to include a power
15 matches
Mail list logo