RE: [Elecraft] K3 with a PW-1

Yes. I later found this: http://www.qth.com/topten/apnote3.htm -Original Message- From: Joe Subich, W4TV [mailto:[EMAIL PROTECTED] Sent: Thursday, November 20, 2008 9:19 PM To: 'Don - W6CZ'; Elecraft@mailman.qth.net Subject: RE: [Elecraft] K3 with a PW-1 Don, A series of FET

[Elecraft] N4PY software

If you are at Dayton, you should stop by Carl at booth 481 and see what functionality N4PY software can add to your K2 (like dual RX!). Don W6CZ ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list.

[Elecraft] troubles with kits

Herb Why don't you start with something like one of the mini-module kits? That will give you an idea of what to expect and let you develop your soldering skills if they are lacking. There are some important things to keep in mind when building kits. One - the right tools - in particular soldering

[Elecraft] Intermittent no RX on 80/160 K2/100 #4029

I thought this problem was related to the T/R switching problem I was having and fixed (a no solder joint), but apparently I though that because I first noticed that failure on 80 meters. So I brought it into work today, and when I hooked it up to a service monitor and put a signal into it - no

Re:[Elecraft] Rediculous, unreasonable and selfish firmware feature request

Not so far fetched - my Icom 703 (nice features - so-so receiver) has that - as well as others I own or have owned. Perhaps it would be easier implement in conjunction with the KRC2 or some similar device. The 703 uses the four buttons along the bottom of the display - 3 memory You could also

[Elecraft] KPA100 T/R Switching Failure

I'll try this again - sorry if it appears twice During SS, one of my K2/100s (4029) failed. No RX and as I recall no TX. It was intermittent at first (and had intermittently shown this symptom before) and to be honest, between fighting a cold and trying to work at least a sweep between family

RE: [Elecraft] KRC2 programming

, October 05, 2004 11:02 PM To: Don Melcher Cc: Elecraft List Subject: Re: [Elecraft] (no subject) Hi Don, See http://www.elecraft.com/images/KRC2config2.JPG This picture is of my last revision of the KRC2 config program. I'm now adding at cutsomer request the ability to save several KRC2

[Elecraft] (no subject)

For inquiring minds ;-) , I'm in the final phase of finishing up the reconfiguration program for the KRC2. I'll post here as I get it wrapped up later this week. 73, Eric WA6HHQ WELL? Don - W6CZ ___ Elecraft mailing list Post to:

Re: [Elecraft] K2 w/ Winlink 2000?

Charles You might try to get a little real world experience with Winlink and PactorIII/II before you write that letter to QST. While the Skymate you have and speak of is a wonderful system and works well, and the buy-in is less if you are starting from scratch (I am a dealer for both), it has

[Elecraft] Re: Hakko 808 wanted

I just did a quick google and came up with $159.95 at Kiesub Electronics in Las Vegas - http://www.kiesub.com/hakko808.htm - $40 less then the 3 or 4 other places I checked. Having been saying that I really need to get a desoldering station for far too long - I ordered one. Don

Re:[Elecraft] K2's and the N4PY Program?

I have not used it in the Dual K2 mode - yet - I have been working on cleaning up the station at home after moving the remote station out and to the permanent remote station location. I finally got a new USB 8 port serial box (so now I have a total of 11 and STILL not enough) and I should get the

[Elecraft] Re: VOX

a No ahhh I don't ah use it ahhh and I don't ahh like it :) I have tried using it mobile but got into problems violating FCC rules when other drivers cut me off. Prefer a boom-mike headset (the original Heil BM10) and a handheld pendant switch and foot switch in parallel. Use

RE: [Elecraft] KRC2 Config utility

Hi Elecrafters, will there be a KRC2 configuration utility in the near future? I would really like to configure the thing via software. I often change antenna configuration in my fieldday setups, but would like to use ONE pre- assembled control-line with water-proof/assembled connectors, etc.

Re: [Elecraft] Insulated Backstay

that up. I am not saying other methods WON'T work - just that it is difficult to predict the results and it can be a tremendous amount of work and expense with poor results. One thing that has been determined is SOME sort of direct sea-water contact is needed. Don Melcher W6CZ HF Radio On Board

Re:[Elecraft] Thoughts on the KDSP2

Wayne - I wonder if you - or anyone else for that matter - has found any values that work better then the default? Don W6ZO ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net http://mailman.qth.net/mailman/listinfo/elecraft You must subscribe