[Elecraft] KXPA100 amp and ATTN switch

I just connected my new KXPA100 to my KX3 via a home-brew KX3-KXPA100 Adapter Cable. Everything works just fine if I have the 3dB attenuator switch set to IN. I fI set it to OUT/AUTO as described in the manual I end up overdriving the amp, meaning the power out is much higher than set on the

Re: [Elecraft] PX3: Possible problem with display

David Thanks for all the info. Wayne seems to have explained it fairly well. I think there were a few contributing factors in my setup. I have a new and quite a bit quieter antenna, thus less noise to cover up the small spikes. I never had the NB on but I had the PRE AMP off on 20M. Most of

Re: [Elecraft] PX3: Possible problem with display

> certain other equipment on that is close to the px3. > If you find a culprit try putting ferrite on the cables. > 73 > > > > Sent from my Samsung Galaxy smartphone. > > ---- Original message > From: Larry Naumann <n...@att.net> > Date: 2016

Re: [Elecraft] PX3: Possible problem with display

en the KX3 and the PX3 in parallel with the RX I/Q cable. The shield from old RG-8 coax works well. 73, Don W3FPR On 9/9/2016 10:12 AM, Larry Naumann wrote: I have just recently noticed that there is a continual spike that follows my cursor. It is internally generated. In CW mode it is away fro

[Elecraft] PX3: Possible problem with display

I have just recently noticed that there is a continual spike that follows my cursor. It is internally generated. In CW mode it is away from my tuned signal by the amount of my CW side tone setting and can be switched to above or below the cursor depending on if I am in CW or CW-R. These spikes

[Elecraft] FS: KX3 Sidekick Endplates, Plastic cover and Think Tank Flash case

I have a set of the Sidekick end plates with plastic cover and a Think Tank flash case that I no longer need. This all fits the KX3. Everything is in very good to like new condition. I got a KX2 so my KX3 is staying home. Asking $65.00 for the package and this includes shipping in CONUSA. PayPal

[Elecraft] K2:Problem with new build. buttons and encoder don't work

I am in the process of building a new K2 and have run into a problem When I do the initial power on testing I get the Elecraft sign then 7.1000 but the encoder And all the buttons do not work. I have checked all my solder joints and the proper placement of parts along with RP's, all Looks

[Elecraft] K3: CWT and Volume wish list

a bunch of extr wires and controls hanging around. I also want to say how much I like running PSK with the paddles, I've had a lot of fun with that feature. Also getting ready to put in the KRX3 module, this ought to really add to the radio. Thanks for a great product. Larry Naumann N0SA -- View

Re: [Elecraft] K3 CW spot feature

I notice the same thing, it seems to not work quite as well as before. The tune indicator seems to not lock on as well either, which makes sense as they are both tied together. Larry N0SA George-122 wrote: Maybe it's just me, but the spot feature seems less accurate than previously.

Re: [Elecraft] K3 Beta Release Update (MCU 2.20, DSP 1.88)

It may be just me but when I go to the link I get version 2.19 not 2.20 wayne burdick wrote: Several customers noticed a problem with noise reduction in yesterday's beta release (MCU 2.19/DSP 1.87). This has been corrected, and we've changed the revisions to 2.20 / 1.88. The files are

Re: [Elecraft] K3 Beta Release Update (MCU 2.20, DSP 1.88)

browser, maybe? ~Iain Larry Naumann wrote on 07/24/08 13:18: It may be just me but when I go to the link I get version 2.19 not 2.20 wayne burdick wrote: Several customers noticed a problem with noise reduction in yesterday's beta release (MCU 2.19/DSP 1.87). This has been

[Elecraft] FS: KPA100

, low power camping rig. Please contact me off list for price etc. [EMAIL PROTECTED] Larry Naumann N0SA ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub

[Elecraft] HI CUR question

checked my output filter tuning and all is good. Is this something to be concerned about or is this in the normal range of xmit current at 10 watts? Larry Naumann N0SA ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber

[Elecraft] AGC question

I am building a K2 and when I try to adjust the AGC voltage the most I can get is just under 3.8 volts, about 3.7 is what I can get. Is this okay or do I have a problem somehwere? Thanks Larry ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net

[Elecraft] FS:KAT2 ATU

for it and that includes shipping in the lower 48. Larry Naumann N0SA ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net http://mailman.qth.net/mailman/listinfo/elecraft You must subscribe to post. Subscriber Info (Addr. Change, Unsub etc