Re: [Elecraft] KPA500 Noise While Off

My KPA500 makes a noticeable hum/thump when the laser printer that is on the same circuit draws a lot of current. 73, Matt NQ6N On Wed, Jun 27, 2018 at 12:58 PM Jim Brown wrote: > On 6/27/2018 10:37 AM, Richard Wade wrote: > > If I had to venture a guess, I would say that somehow the

Re: [Elecraft] KPA1500 ATU - ability to handle more than two antennas

the switching in of a 40m bandpass filter after the amp, and then whichever antennas are usable on 40m, with the tuner knowing which antenna was chosen so that it can switch to the previously known settings for instant TX. 73, Matt NQ6N On Fri, Jan 26, 2018 at 1:45 PM, K9MA <k...@sdellington

Re: [Elecraft] Operation of K Line Over LAN

One other note: there is also a remotehams Android app which can also be used for operating the rig via rcforb on phone. On Thu, Jan 11, 2018 at 7:10 PM Matt NQ6N <m...@nq6n.com> wrote: > Remotehams rcforb works nicely and is easy to set up especially if you > already have

Re: [Elecraft] Operation of K Line Over LAN

Remotehams rcforb works nicely and is easy to set up especially if you already have a sound card connection for digital modes. It does require one pc near the rig and another near the bed. You can easily connect up a paddle using a serial port or usb serial adapter. 73, Matt NQ6N On Thu, Jan

Re: [Elecraft] [KX3] Re: KX2 as a remote front panel for another KX2, KX3, or K3S?

for casual operating or DXing. The operating position where I operate from when using the remote setup is a smallish desk with a slim iMac and not much extra space. 73, Matt NQ6N On Fri, Dec 22, 2017 at 7:09 PM, kevino z z_kev...@hotmail.com [KX3] < kx3-nore...@yahoogroups.com> wrote: >

Re: [Elecraft] WSJT-X K3/K3s hanging as Tx

the sort of behavior being experienced. 73, Matt NQ6N On Tue, Nov 14, 2017 at 8:07 AM, David Bunte <dpbu...@gmail.com> wrote: > I won't take a lot of time weighing in on this thread. I am a newbie to > FT8, with only a little over 100 Qs. I am using my K3 with a DigiKeyer II, > and

Re: [Elecraft] On CW

. I think there is something very special about the art form of CW and the kind of craftsmanship and passion that it inspires. Thanks to Wayne and everyone at Elecraft, the CWOps, etc, for keeping the magic alive. 73, Matt NQ6N On Tue, Oct 31, 2017 at 1:26 PM, <rkr...@johngalt.biz>

[Elecraft] For Sale: One excellent condition, late serial number K3

numbers are 5530 and 6066. I am the original purchaser of both rigs and both are in superb working order. 73, Matt NQ6N __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm

Re: [Elecraft] [KX3] Re: Kx2 paddle issue

manufactured with a slightly larger hole in the plastic, then it would be easier to achieve a tight fit between the screw and the standoff. I'd also be curious if a small lock-washer on the standoff side might help make the assembly more immune to vibration. 73, Matt NQ6N On Tue, Jul 25, 2017 at 11:12

[Elecraft] using the KX2 as a remote control head for K3

using RCForb connected to the K3 in the shack, but also have an RRC remote unit and would consider any other options. 73, Matt NQ6N __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http

Re: [Elecraft] KPA500 Hum when off?

I had this happen and discovered that the laser printer I had was plugged into the same ac circuit and was causing voltage drop periodically. Moving the printer to another wall outlet fixed the problem. Matt NQ6N On Jun 11, 2013, at 5:03 PM, Eric Swartz - WA6HHQ, Elecraft e...@elecraft.com