I'd experienced this problem, also not due to RF in the shack, and since I switched to using PTT via RTS or DTR the problem has not recurred. The problem began when I had been using RCForb and a virtual serial port with CAT control of PTT for WSJT-X, so the explanation Joe offers makes sense based on my experience.
Unless WSJT-X had some provision for reviewing all state changes to the K3 that might occur "unexpectedly" due to other CAT "clients" of the K3, it would not be able to guarantee that its own state matched that of the K3, which could seemingly result in the sort of behavior being experienced. 73, Matt NQ6N On Tue, Nov 14, 2017 at 8:07 AM, David Bunte <[email protected]> wrote: > I won't take a lot of time weighing in on this thread. I am a newbie to > FT8, with only a little over 100 Qs. I am using my K3 with a DigiKeyer II, > and have never experienced the problem. > Dave - K9FN > > On Tue, Nov 14, 2017 at 8:58 AM, Gordon LaPoint <[email protected]> > wrote: > > > Bert, > > I also have the problem, and it IS NOT rf getting into the shack. It > > will happen with 1 watt. It is a function of wsjt-x and may be related > to > > using split. I have never seen the problem when NOT using split. The > > problem usually appears when clicking on a new station to answer a CQ, > and > > the split has to change. > > The systems will return to normal in the next 15 second segment if > > nothing else is touched, or somtimes will return to normal sooner if the > > "halt tx" button is clicked on. > > I also see the problem when using other radios than the K3, I have an > > IC-7000 and ANAN-10E that also get used for wsjt-x. > > The problem has occured in wsjt-x versions 1.8 rc2, rc3 and release > > 1.8 I not remember seeing the problem before version 1.8 rc2, but can > not > > be sure. > > I now have about 1,500 FT8 contacts in the log, so I use FT8 a lot. > > Gordon - N1MGO > > > > On 11/13/2017 07:00 PM, Bert Garcia N8NN wrote: > > > >> The CAT and PTT are on different COM ports, per the installation > >> instructions for the microKEYER II when using WSTJ-X. And it's not a > stray > >> RF problem as I have all the equipment bonded together, ferrite cores on > >> the audio and control lines, a line isolator in the feedline where it > >> enters the house, and line isolators between the rig and amp and between > >> the amp and antenna tuner. The lockup happens when running only 30 > watts > >> with FT8. It never happens when running a KW on many other modes. I > run > >> RTTY, PSK and other digital modes with no problems. > >> > >> Thus, I suspect the issue is associated with the WSRJ-X software as the > >> same issue occurs with various transceivers in multiple locations. > >> > >> Bert N8NN > >> > >> -----Original Message----- > >> From: Don Wilhelm [mailto:[email protected]] > >> Sent: Monday, November 13, 2017 3:17 PM > >> To: [email protected]; [email protected]; [email protected] > >> Subject: Re: [Elecraft] WSJT-X K3/K3s hanging as Tx > >> > >> Bert and Gary, > >> > >> Have you looked for a computer problem? Such as having both PTT via > >> command and via an RS-232 signal line? Do you have both VOX on and > another > >> means of keying the transceiver? > >> > >> 73, > >> Don W3FPR > >> > >> On 11/13/2017 3:07 PM, Bert Garcia N8NN wrote: > >> > >>> This problem is not unique to the K3. My Yaesu FT-1000mp does the > >>> same thing -- locks up in transmit mode with no RF output and I have > >>> to turn it off to regain control. The lock up is intermittent, and > >>> some days it never happens. Rebooting everything works for a while, > >>> but when I least expect it, the lockups will start again. > >>> > >> ______________________________________________________________ > >> Elecraft mailing list > >> Home: http://mailman.qth.net/mailman/listinfo/elecraft > >> Help: http://mailman.qth.net/mmfaq.htm > >> Post: mailto:[email protected] > >> > >> This list hosted by: http://www.qsl.net > >> Please help support this email list: http://www.qsl.net/donate.html > >> Message delivered to [email protected] > >> > > > > > > -- > > Gordon - N1MGO > > > > ______________________________________________________________ > > Elecraft mailing list > > Home: http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/mmfaq.htm > > Post: mailto:[email protected] > > > > This list hosted by: http://www.qsl.net > > Please help support this email list: http://www.qsl.net/donate.html > > Message delivered to [email protected] > > > ______________________________________________________________ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[email protected] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to [email protected] > ______________________________________________________________ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:[email protected] This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to [email protected]
