The only difference is I us hardware estop force estop sense low, and when I
release my estop button ,estop sense goes high and then I turn the machine on
through the gui halui and off she goes ,I'm running EMC2.6.15 halui_halvcp
configs My (standard pinout) file is below your response "Jon Els
Greetings;
In the transition to emc2, I noticed that the directory emc/programs seems to
have become deprecated.
I found where they were relocated to, but the install script needs to edit
stepper_inch.ini to add a trailing '/' to the PROGRAM_DEFAULT path, which was
properly set to ~/user/emc2/
Stephen Wille Padnos wrote:
> Jon Elson wrote:
>
>
>>Actually, he's got the PPMC, the analog servo board set.
>>But, the problems are the same, it all is in the encoder handling.
>>
>>With the Gecko drive, the encoders are powered off the Gecko,
>>and there could be noise issues with trying to h
Hi all,
After the success I've had with EMC2 and my minimill, I've decided to take a
whack at converting a little Prazi 5x12 lathe I have. So far I've got it
"steppered" and I have procured a PC on which I've installed EMC2 from the live
CD. So far so good.
On the minimill I'm using a PMDX
Jon Elson wrote:
>Actually, he's got the PPMC, the analog servo board set.
>But, the problems are the same, it all is in the encoder handling.
>
>With the Gecko drive, the encoders are powered off the Gecko,
>and there could be noise issues with trying to hook the index
>signal to the USC board.
Stephen Wille Padnos wrote:
> Jon Elson wrote:
>
>
>>[snip]
>>
>>I could send you an EPROM for the PWM controller if you want,
>>the stepper hasn't been fully updated yet until I find out what
>>is going on, here. None of this makes sense unless you have an
>>encoder with index pulse, so few
> > >> net Xindex axis.0.index-enable ppmc.0.encoder.00.index-enable
> > >> net Xindex axis.1.index-enable ppmc.0.encoder.01.index-enable
> > >> net Xindex axis.2.index-enable ppmc.0.encoder.02.index-enable
>
On Wed, May 23, 2007 at 06:23:14AM -0700, Mark Pictor wrote:
> Shouldn't this cause an er
Do you get this behavior with one of the "sim" configurations (e.g.,
sim/axis.ini, sim/tkemc.ini)? What is the exact sequence of operations
you do (key presses, button clicks, etc) to make this happen? If you
are not running the newest version of emc2 (2.1.5), does the problem
still occur after y
Jon Elson wrote:
> [snip]
>
>I could send you an EPROM for the PWM controller if you want,
>the stepper hasn't been fully updated yet until I find out what
>is going on, here. None of this makes sense unless you have an
>encoder with index pulse, so few stepper controller users will
>run into
--- John Kasunich <[EMAIL PROTECTED]> wrote:
> Stephen Wille Padnos wrote:
>
> >> # connect index pulses to motion controller
> >> # do these when index pulsing is figured out
> >> net Xindex axis.0.index-enable ppmc.0.encoder.00.index-enable
> >> net Xindex axis.1.index-enable ppmc.0.encoder.01
First off I have managed to get EMC2 Live loaded onto a computer and
running. Lots of changes since the last time I looked at EMC, I really
like the graphics in the AXIS interface, makes debugging programs a lot easier.
I did translate a program that was running on a Fanuc control and got it t
Inside the ini file you are using there are the following lines:
#HALFILE = xylotex_pinout.hal
HALFILE = standard_pinout.hal
simlpy remove the comment character '#' from the first line, and add it to
the second one.
Regards,
Alex
- Original Message -
From:
Yes Sven you are dead right, the mistake I was making was trying to do it
using Nero SmartStart which would have been alright if I had closed the
window that appears and gone straight to Recorder then Burn Image. However I
did persivere and eventually work it out. I have now had Ubuntu+EMC2
ins
13 matches
Mail list logo
