Our group (details at http://www.linuxcnc.org) develops a free software
machine tool control program. One of our best developers extended xfig
to convert electronic drawings to the type of data used as input to
computer controlled machine tools. We try to be diligent about licensing
issues, and the
On Tue, Jun 26, 2007 at 07:13:36PM -0500, RogerN wrote:
> Or maybe my question should be how do you set up the TLO table
> for lathes?
>
> Sorry for such a basic question but I'm new to EMC2 and lathes and
> haven't been able to find a procedure for this in the documentation or
> through google
Kirk Wallace wrote:
> I need to have a collet open and close code (M21/M22 ?) for my Hardinge
> HNC project. I noticed in the Tool Change literature, that changes where
> needed in iosh and tkio.sh . I would also think that changes would be
> needed in the interpreter to add M21/M22. Another issue
Currently I set tool 1 the proper distance from the chuck, touch off,
and enter 0. Next I jog a skim cut, calculate radius, touch off, and
enter my calculated radius. How do you set the offsets for another
tool? Or maybe my question should be how do you set up the TLO table
for lathes?
Sorr
On Tue, 2007-06-26 at 09:55 -0700, Kirk Wallace wrote:
> On Tue, 2007-06-26 at 11:29 -0500, Sam Sokolik wrote:
> > How much main memory is in the computer? You need at least 256mb and some
> > people have needed more - like 512mb during the installation.
>
> I had the same problem. My computer r
IANAL, but as I read the license says that there are NO restrictions as
to it's use in any way.
> "with the only requirement
> being that the above copyright and this permission
> notice remain intact."
or am I missing the point somewhere?
Dale
Chris Radek wrote:
>
Hi,
so we can just close the case and forget about a public version of this. I
could remove the text support from xfig, but i just don't think i want to as
the current version works fine for me which imho is within the GPL.
Perhaps someone will do a similar thing for inkscape or so. Whoever wan
I need to have a collet open and close code (M21/M22 ?) for my Hardinge
HNC project. I noticed in the Tool Change literature, that changes where
needed in iosh and tkio.sh . I would also think that changes would be
needed in the interpreter to add M21/M22. Another issue that comes to
mind is, can I
On Tue, 2007-06-26 at 11:29 -0500, Sam Sokolik wrote:
> How much main memory is in the computer? You need at least 256mb and some
> people have needed more - like 512mb during the installation.
I had the same problem. My computer runs Ubuntu okay with 128mB but
would not install. Of the two PC's
How much main memory is in the computer? You need at least 256mb and some
people have needed more - like 512mb during the installation.
http://wiki.linuxcnc.org/cgi-bin/emcinfo.pl?Hardware_Requirements
sam
- Original Message -
From: "Kasparov, Aram" <[EMAIL PROTECTED]>
To: "Enhanced Ma
Hello.
During CNC workshop (Galesburg) I found that my computer Compaq AMD64 behaves
differently than any other computers. EMC2 real time test doesn't work on my
computer and at the same time it still ran my driver/machine properly. Nobody
can find the problem.
Yesterday I tried load UB
chris wrote:
> On Tue, Jun 26, 2007 at 09:07:05AM -0400, Paul Fox wrote:
> >
> > of course, chris, as copyright holder for his code could make
> > an exception for the xfig use, if he were so inclined. i don't
> > think he needs to, or should, but he could. (and he could give
> > that vers
On Tue, Jun 26, 2007 at 09:07:05AM -0400, Paul Fox wrote:
>
> of course, chris, as copyright holder for his code could make
> an exception for the xfig use, if he were so inclined. i don't
> think he needs to, or should, but he could. (and he could give
> that version a license just as "restrict
till harbaum / lists wrote:
> ... source code up and in the progress of doing so i noticed
> that i just cannot comply to the GPL as i cannot put xfig
> under GPL (the xfig license does not allow me to
> remove/restrict its license) or put Chris code under the xfig
> license (the GPL does not
14 matches
Mail list logo