> On Apr 3, 2016, at 7:32 AM, Valerio Bellizzomi wrote:
>
> so now you can retry my config problably this time with luck :-)
HI Valerio,
It was pretty forgiving on the timing settings - we used the Sherline defaults.
Best,
Jeshua Lacock
Founder/Engineer
<3DTOPO.com>
On Sat, 2016-04-02 at 18:00 -0600, jeshua wrote:
> > On Mar 28, 2016, at 6:01 PM, Gene Heskett wrote:
> >
> > On Monday 28 March 2016 19:48:26 Gene Heskett wrote:
> >
> >> On Monday 28 March 2016 16:21:36 jeshua wrote:
> On Mar 26, 2016, at 7:50 AM, Sarah Armstrong
>
> On Mar 28, 2016, at 6:01 PM, Gene Heskett wrote:
>
> On Monday 28 March 2016 19:48:26 Gene Heskett wrote:
>
>> On Monday 28 March 2016 16:21:36 jeshua wrote:
On Mar 26, 2016, at 7:50 AM, Sarah Armstrong
wrote:
this all
On Mon, 2016-03-28 at 14:26 -0600, jeshua wrote:
> > On Mar 28, 2016, at 12:49 AM, Valerio Bellizzomi wrote:
> >
> > I had to configure a tb6560 with nema 34 motors, like that:
> >
> > step time: 1
> > step space: 1000
> > step hold: 1000
> > step setup: 1
>
> Hi
On Monday 28 March 2016 19:48:26 Gene Heskett wrote:
> On Monday 28 March 2016 16:21:36 jeshua wrote:
> > > On Mar 26, 2016, at 7:50 AM, Sarah Armstrong
> > > wrote:
> > >
> > > this all depends if you have connected the EN - ( enable - ) of
> > > the stepper drives
On Monday 28 March 2016 16:24:15 jeshua wrote:
> > On Mar 26, 2016, at 9:25 PM, Gene Heskett wrote:
> >
> > And I looked at my 2m542's today, and found nothing attached to the
> > enable terminals, + or - side. I was thinking they defaulted to on
> > if not specifically shut
On Monday 28 March 2016 16:21:36 jeshua wrote:
> > On Mar 26, 2016, at 7:50 AM, Sarah Armstrong
> > wrote:
> >
> > this all depends if you have connected the EN - ( enable - ) of the
> > stepper drives ,
> > all the + pins go to 5v
> > step - = pul & dir - =
On Monday 28 March 2016 16:18:18 jeshua wrote:
> > On Mar 26, 2016, at 7:13 AM, Gene Heskett wrote:
> >
> > I am not fam with that driver Jeshua, but most of these drivers
> > have 3 inputs, step, dir, and enable. I suspect the enable might not
> > be wired correctly. In my
> On Mar 28, 2016, at 12:49 AM, Valerio Bellizzomi wrote:
>
> I had to configure a tb6560 with nema 34 motors, like that:
>
> step time: 1
> step space: 1000
> step hold: 1000
> step setup: 1
Hi Valerio,
I just tried those values, no luck.
> however the wirings
> On Mar 26, 2016, at 9:25 PM, Gene Heskett wrote:
>
> And I looked at my 2m542's today, and found nothing attached to the
> enable terminals, + or - side. I was thinking they defaulted to on if
> not specifically shut off, so my memory was correct. I too have heard
>
> On Mar 26, 2016, at 10:32 AM, Dave Cole wrote:
>
> There are many web pages on issues with those TB6560 boards and how to
> fix them.Many of the webpages end with "this was not worth the
> effort" type messages.
> I would avoid the TB6560 boards.
Hi Dave,
Well
> On Mar 26, 2016, at 7:50 AM, Sarah Armstrong
> wrote:
>
> this all depends if you have connected the EN - ( enable - ) of the stepper
> drives ,
> all the + pins go to 5v
> step - = pul & dir - = direction
>
> if you have it's probable that you have this
> On Mar 26, 2016, at 7:13 AM, Gene Heskett wrote:
>
> I am not fam with that driver Jeshua, but most of these drivers have 3
> inputs, step, dir, and enable. I suspect the enable might not be wired
> correctly. In my setups, using the 2m542 driver, IIRC leaving the
>
On Sat, 2016-03-26 at 00:49 -0600, jeshua wrote:
> Greetings,
>
> I am attempting to assist a friend setting up a HY-JK02-M 5-axis Interface
> Board with Axis running HY-DIV168N-3.5A drivers.
>
> Controller Manual: http://www.tecnoflexo.com.br/site/fotos/download/17/17.pdf
> Driver Manual:
>
On Saturday 26 March 2016 12:32:28 Dave Cole wrote:
> On 3/26/2016 1:49 AM, jeshua wrote:
> > Greetings,
> >
> > I am attempting to assist a friend setting up a HY-JK02-M 5-axis
> > Interface Board with Axis running HY-DIV168N-3.5A drivers.
> >
> > Controller Manual:
> >
On 3/26/2016 1:49 AM, jeshua wrote:
> Greetings,
>
> I am attempting to assist a friend setting up a HY-JK02-M 5-axis Interface
> Board with Axis running HY-DIV168N-3.5A drivers.
>
> Controller Manual: http://www.tecnoflexo.com.br/site/fotos/download/17/17.pdf
> Driver Manual:
>
this all depends if you have connected the EN - ( enable - ) of the stepper
drives ,
all the + pins go to 5v
step - = pul & dir - = direction
if you have it's probable that you have this inverted or requires inverting
, for testing just leave this unconnected until you have everything running
On Saturday 26 March 2016 02:49:55 jeshua wrote:
> Greetings,
>
> I am attempting to assist a friend setting up a HY-JK02-M 5-axis
> Interface Board with Axis running HY-DIV168N-3.5A drivers.
>
> Controller Manual:
> http://www.tecnoflexo.com.br/site/fotos/download/17/17.pdf Driver
> Manual:
>
Greetings,
I am attempting to assist a friend setting up a HY-JK02-M 5-axis Interface
Board with Axis running HY-DIV168N-3.5A drivers.
Controller Manual: http://www.tecnoflexo.com.br/site/fotos/download/17/17.pdf
Driver Manual:
19 matches
Mail list logo