ok well im an et in the navy so i might be able to help, now you have ip addresses and
hub and new cables however you must also check access rights now usually with a unix
based system there are host databases which contain ip address host name and security
access(may or may not be included)
You know, Collins, it was pretty weird, and it went something like this: Suppose the
network was
down. Then if i tried to bring up the card with 'ifconfig eth1 netmask 255.255.255.0
192.168.1.1'
then the FIRST time i tried that it would reply with something like "SIOCSIFADDR:
Cannot assign
I have a little program that you can run on two machines., and it sends
and listens without reference to anything else, without ip numbers or anything.
I can e-mail you this if you require, and it will eliminate the hardware for
you. I ran into this problem, and found it was simply
I would appreciate it very much if you do that
Thanks in advance
Declan Moriarty wrote:
I have a little program that you can run on two machines., and it sends
and listens without reference to anything else, without ip numbers or anything.
I can e-mail you this if you require, and
i am tryint o reconnect my home LAN but I can't getmy machines to ping
each
other. Everything is fine. IP configuration is right, HUB is working,
cables
are new and connected. Don;t know what the problem may be
At 09:24 AM 4/3/2001 -0700, [EMAIL PROTECTED] wrote:
i am tryint o reconnect my home LAN but I can't getmy machines to ping
each
other. Everything is fine. IP configuration is right, HUB is working,
cables
are new and connected. Don;t know what the problem may be?
what does 'route -n' show?
Also, have each machine try pinging itself, in other words:
ping 127.0.0.1
ping localhost
If those don't work, there is something wrong with the networking
software on each machine. (I can't help you with the next step, but
someone can -- post your results.)
Randy Kramer
Dan Swartzendruber
I tried that and each machine can ping itseld and gets responses, but can't
ping the other machine. In other words, win95 can ping itself but not linux and
linux can ping itself but not win95.
Randy Kramer wrote:
Also, have each machine try pinging itself, in other words:
ping 127.0.0.1
At 11:57 AM 4/3/2001 -0700, [EMAIL PROTECTED] wrote:
I tried that and each machine can ping itseld and gets responses, but can't
ping the other machine. In other words, win95 can ping itself but not
linux and
linux can ping itself but not win95.
and the routing tables?
how do I get those? is the route command?
Dan Swartzendruber wrote:
At 11:57 AM 4/3/2001 -0700, [EMAIL PROTECTED] wrote:
I tried that and each machine can ping itseld and gets responses, but can't
ping the other machine. In other words, win95 can ping itself but not
linux and
linux can
Well, until someone else chips in:
Try having each machine ping itself using its assigned IP address (like
192.168.1.1 or whatever).
All of your cables plugged in properly?
Do you have a crossover RJ-45 cable by any chance that you could use to
connect the two machines, replacing the hub
cables pluged in properly
they ping themselves but not the other machine
yes, I had the LAN running but had to reinstall win95 and the lost connection,
haven't been able to reconnect ever since
yes, hub has LED but nothing happens when i ping the other machine
Randy Kramer wrote:
Well, until
At 12:15 PM 4/3/2001 -0700, you wrote:
how do I get those? is the route command?
route -n
I had a problem similar to this awhile back. Everything looked like it *should* be
working but it
wasn't. Pinging the local ip was fine but pinging the other box was not. After much
fiddling of
bringing things up down and many rebootings of the Windows box. We finally left it
set up so
that
What is the result of the command ifconfig?
- Original Message -
From: [EMAIL PROTECTED]
To: [EMAIL PROTECTED]
Sent: Tuesday, April 03, 2001 11:24 AM
Subject: [expert] ping, ping, doesn't ping
i am tryint o reconnect my home LAN but I can't getmy machines to ping
each
other
On Tuesday 03 April 2001 01:46 pm, you wrote:
At 12:15 PM 4/3/2001 -0700, you wrote:
how do I get those? is the route command?
route -n
There is a pretty good HOWTO on my website for setting up Linux to Linux
networking. A lot of the same info will apply to Linux to Windows setup,
Is either machine connected to the Internet? If so, can you ping out to
somewhere on the net by IP? And try pinging from a web-based ping engine
back to the machine connected to the Internet.
At 03:46 PM 4/3/2001 -0400, you wrote:
At 12:15 PM 4/3/2001 -0700, you wrote:
how do I get those? is
Indeed, your howto is very good. I have most of te settings in your howto
in my network configuration on both machines and don't work. I tried a
suggestion someone lelse gave me, but it didn't work ether. I am so tired
and i give up
Ken Thompson wrote:
On Tuesday 03 April 2001 01:46 pm, you
that sounds interesting. What would that tell me. and where is siuch as
web-based pinging machine?
Karl Cunningham wrote:
Is either machine connected to the Internet? If so, can you ping out to
somewhere on the net by IP? And try pinging from a web-based ping engine
back to the machine
Give up today, come back tomorrow or in a few days. Sleep on it, read
about it, but also relax. It would be helpful to have another machine
that works, and see if you can talk to one of these two machines -- I
would be surprised if they both have a problem, I suspect only or the
other has the
On 03,Apr/01 22:40, David C. Hoos, Sr. wrote:
all this lot sounds suspiciously familiar.
I too originally had a working LAN with a W2K machine talking to this
Mandrake box using Samba.
Then along came the hard disc failure rebuild from CD backups.
I used a Mandrake re-install to alter my
On Tue, 3 Apr 2001 14:57:35 -0700 (PDT)
John Wolford [EMAIL PROTECTED] wrote:
snips
rebooted the linux machine (mdk
7.1). For some CRAZY
reason, this worked and all of a sudden we were able to ping accross the
network. I"m convinced it
had something to do with the network card and linux
I've tried all of that reboot, manually stopping and restart network, nothing
seems to work
Collins Richey wrote:
On Tue, 3 Apr 2001 14:57:35 -0700 (PDT)
John Wolford [EMAIL PROTECTED] wrote:
snips
rebooted the linux machine (mdk
7.1). For some CRAZY
reason, this worked and all of a
[EMAIL PROTECTED] wrote:
I've tried all of that reboot, manually stopping and restart network, nothing
seems to work
OK, tell me what the following files have in them:
/etc/sysconfig/network
/etc/sysconfig/network-scripts/ifcfg-lo
/etc/sysconfig/network-scripts/ifcfg-eth0
/etc/modules.conf
24 matches
Mail list logo
