GA All,
If some of you are running MixW using VAC, how do you control the AF
level and thus the output power? Previously on my K2, I would set it
to maximum power, about 12 watts, and control the AF level to get an
output of about 5 watts peak. As I burned out the finals on one
transceiver
Hi,
In Pre 14, I was testing power level and using companding and
compression in an attempt to increase the average power level. In
pre 14, the average power level is down compared to pre 12, because
of the new ALC. I connected an external audio generator and a scope,
but this produces a
GM,
I was using MixW last night, and I noticed that CAT worked all night
and still was on this morning. Good job fixing it. I can't get any
audio from the Mike when VAC is checked on. The VAC works if you
check Auto VAC, uncheck VAC and the mode is SSB. Note that you can
check both VAC
Chris,
I had a problem with it in Pre 13 because once I needed it. I just
tried it in Pre 14 and it knocks a carrier down about 20 dB. Seems
it could do better.
73, Chas W1CG.
At 03:40 PM 2/11/2006, Christoph - HB9AJP wrote:
Hi
I find the ANF (Automatic Notch Filter) not working
to
share the design of it (in English) so that other authors will not
ever waste their time with the real single sample LMS again. Even
if you have real signals, the block LMS is accomplished in exactly
the same way, but real FFT's are used.
Bob
N4HY
Charles Greene wrote:
Chris,
I had
Hi,
There's an item that I noticed in preview 12 and also in preview
13. When in Setup under the Transmit tab, you have the ability to
define your own profile and save it. But when you restart Power
Console, the saved profile is not there any more.
73, Chas W1CG
Mike,
I haven't done it, but you need two things as I see it, based on
running two copies of MixW, HRD, or N4PY talking to two different
transceivers. You need to designate two separate ways to talk to the
hardware, and the only way I know of to do this is to use two sound
cards and the
Gerald and All,
The whole area of a SDR is one that is going to
require a lot of technical hand-holding for the
average ham, so you need to address this fact.
On the subject of having two reflectors, I was
and still am, on a reflector about antennas where
there was a lot of technical talk
GM,
I was trying to do some image reduction on the TX signal, and I set
up a distant receiver and set the PowerSDR Console to AM. The
transmitted signal was on 3.9 Mhz and the receiver read 3.878
KHz. On SSB and CW, signal frequency is right on. Tried another
receiver, the same. Put on a
are reversed on audio going into the
sdr-1000.
73 - Mike WA8BXN
---Original Message---
From: Charles Greene
Date: 02/01/06 08:16:32
To: FlexRadio@flex-radio.biz
Subject: [Flexradio] Frequency on AM
GM,
I was trying to do some image reduction on the TX signal, and I set
up a distant
GM,
Now that I have everything on my Power Console, pre 12 working with
the Firebox except some CAT issues (previously reported), I want to
set up the finer points. What are the proper settings for Compand,
Compression and the transmit equalizer? How do you know, and how do
you test it?
Richard,
I had the same problem two days ago. I tried
everything but could not get the MOX to stop
closing on SSB every time I turned to the Power
Console Then I noticed my mouse did not move
when I started the computer. I am using the USB
to parallel adapter. So I re seated all of my
John,
Array solutions
http://www.arraysolutions.com/prod_category.htm sells two kinds of
filters, the ICE and the W3NQN filters. I bought the W3NQN filters a
couple of years ago as I thought the specs were a little better and
they are good for 200 watts. I am very pleased with the ones I
Hi,
I have a 1 KHz tone on my signal when transmitting SSB. The 1KHz
signal is about 20 dB over the noise level at that frequency. It
does not occur when using VAC, and it does not occur when I key using
MOX with no mike is plugged in. I am using a Firebox. When I plug
a mike into the
, but this does seem to work with the Virutal
Serial Port) When It does loose connection of I simply uncheck Use Cat in
PowerSDR and recheck it and it immediately starts communicating again. I do
not have to restart PowerSDR.
73,
John KD8K
- Original Message -
From: Charles Greene [EMAIL PROTECTED
Lee,
You obviously need two antennas and two sets of
analog components. Why don't you try the AmQRP
Soft Rock 40 as a second analog device? You may
be able to run two copies of Power SDR Console
from different directories. You should also be
able to run SO2R which may be of interest to
Congrats Richard. You are on the right track.
73, Chas, W`1CG
At 08:20 AM 1/7/2006, Richard Stouffer wrote:
I've been a ham for just over a year. I bought my SDR1000 a couple
of months ago after struggling with an ICOM 706 with limited
success. This morning I made my first international 40
Eric and all,
I did the below, and installed the revised Pre 10. Won't run. Get a
fatal error.
73, Chas W1CG
At 05:51 PM 1/4/2006, Eric Wachsmann - FlexRadio wrote:
The best way to do this is to go through the Control Panel -
Add/Remove Programs and remove Preview 10 there. That should
Rich,
It was a cockpit problem. I had the AGC set on fixed and the fixed
AGC gain set too low. Once I set the AGC to any other setting, I had
plenty of audio. It really was not related to the Firebox.
73, Chas, W1CG
At 05:34 PM 1/4/2006, Rick Fletcher, KG6IAL wrote:
Hi, Charles:
A
Hello,
I am also having problems with the radio transmitter shutting down on
high reverse power right after I have tuned it. Running Beta 1.4.5
pre 9. Antenna is Hustler 6BTV, which without the tuner has a SWR on
40 CW of about 1.4:1. Mode CW, power 40 watts. I will try in bypass
and see
Hi,
Where can I download ver 1.4.4? I found the source code on the
download section of the site, but not the compiled code.
73, Chas, W1CG
Hi,
I need the Kenwood TS-2000 and the SDR-1000 CAT commands. I looked
on the site and didn't see any. I need them to make up some macros
that send CAT commands to the radio under control from MixW via the
CAT port; items like selecting filters and other commands not in the
usual set of
Hi,
I have VAC and VCOM installed and working well. I take it that it is
proper to turn VAC off in order to operate SSB from a mike. MixW CW
and all digital modes work well, and my external keyer works well in
parallel with keying CW with MixW from macros or from the
keyboard Now to
Hello,
I am trying to set up MixW with the SDR-1000. I have MixW v2.16b8
and SDR-1000 v 1.4.5BP7.
I have problems in both BPSK31 and CW. First BPSK31. I followed the
steps in Bob's paper exactly through figure 12. MixW receives
ok. On Transmit. the power level fluctuates between 0 and
://www.itsco.com )
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Charles Greene
Sent: Wednesday, December 21, 2005 6:04 AM
To: FlexRadio@flex-radio.biz
Subject: [Flexradio] Beginner Needs Help
Hello,
I am trying to set up MixW with the SDR-1000. I have MixW
Hi,
I am doing the initial configuration on my SDR-1000/100 and ran into
a problem getting the N8VB vCom driver to work per the SDR1000
manual. I am using a Firebox sound card. Computer is 2.16 Mhz
Athlon with 448 MB RAM Only 1 hardware COM port is installed and is
working. There are
Hi,
I am using a Firebox sound system and I am having trouble getting
both a decent audio level for my speakers and drive for the PA by
changing the settings on the Firebox mixer. It doesn't perform
logically as far as I can tell. Can anyone tell me what the Firebox
settings should be?
John,
I have one of the Radio Shack line isolators you mentioned. I use one of
the stereo channels for input and the other for output for psk31 and other
data modes. It works well up to 4 KHZ which is what I have tested it to
but I haven't tried it on the SDR-1000. RS also sells a single
Frank,
I recall from my early RTTY days that switching between two tone generators
produces non coherent RTTY while shifting the tone of a single generator
gives coherent RTTY. Coherent vs non-coherent has to do with the
continuity of the AC waveform of the tone, where coherent is a
201 - 229 of 229 matches
Mail list logo
