?
Dan
On Mon, 2010-06-14 at 15:05 -0500, Daniel Davidson wrote:
We have had a radius server running for years that we use to
authenticate our wireless users over wpa. It works flawlessly and
connections are authenticated as shown by the log below.
Mon Jun 14 14:57:40 2010 : Auth: Login OK
I am migrating our system to freeradius2, I have a test environment that
works well on my fedora system that I am moving to a new server.
I can authenticate with the server perfectly if I start the server using
radiusd -X, however if I then cancel that and run it with the RHEL
startup script it
Nevermind, selinux was biting me in the rear again.
Dan
On Mon, 2010-08-23 at 15:33 -0500, Daniel Davidson wrote:
I am migrating our system to freeradius2, I have a test environment that
works well on my fedora system that I am moving to a new server.
I can authenticate with the server
For some ready my accounting information isnt being written at all, even
though I cannot find a difference in the config file with another radius
server I am running. I have included what I believe to be the
appropriate parts or radiuxsd -x below. Seems like the
%{Client-IP-Address} directories
My new wireless network tested great, but now that I have rolled it out
to the entire building, I get error messages like:
Mon May 2 15:15:06 2011 : Error: rlm_ldap: ldap_search() failed: Timed
out while waiting for server to respond. Please increase the timeout.
And when these trigger,
On 05/03/2011 05:00 AM, freeradius-users-requ...@lists.freeradius.org
wrote:
Daniel Davidson wrote:
My new wireless network tested great, but now that I have rolled it out
to the entire building, I get error messages like:
Mon May 2 15:15:06 2011 : Error: rlm_ldap: ldap_search
I finally got this figured out. It did not have anything do do with
freeradius, but since others using the program might run into it, I
figured I should post it here.
The arp cache of the server was limited by default to 128 addresses,
which was running out pretty quickly. So I inserted and
So is there a way to have users authorize themselves with an LDAP
server, and what is the process for doing that? Use PAM and set the
system up to have PAM auth against LDAP?
Dan
On Tue, 2004-11-02 at 09:40, Alan DeKok wrote:
Daniel Davidson [EMAIL PROTECTED] wrote:
I am sure this has been
On Tue, 2004-11-02 at 11:43, Alan DeKok wrote:
Daniel Davidson [EMAIL PROTECTED] wrote:
So is there a way to have users authorize themselves with an LDAP
server, and what is the process for doing that? Use PAM and set the
system up to have PAM auth against LDAP?
No. You already have
What should default Auth-type be set to then? Right now I am getting a:
auth: No authenticate method (Auth-Type) configuration found for the
request: Rejecting the user
error message from the daemon.
thanks again,
Dan
On Tue, 2004-11-02 at 17:10, Alan DeKok wrote:
Daniel Davidson [EMAIL
It never gives one with this configuration, it just keeps repeating the
same request over and over again, never accepting or rejecting after the
Access-Challenge is sent back to the access point.
Dan
On Thu, 2004-11-04 at 10:48, Alan DeKok wrote:
Daniel Davidson [EMAIL PROTECTED] wrote
Thanks for the info, now we are getting somewhere I just have unchecked
the validate server certificate area for now. Now I am getting a
rejection. Any ideas?
thanks again for the help,
Dan
rad_recv: Access-Request packet from host 128.174.124.2:1024, id=0,
length=224
User-Name =
I uncommented and did appropriate changes (below) to the ldap section of
the modules area. What else needs done? I am deleting the commented
lines.
Dan
ldap {
server = lap server's real name
basedn = ou=People,dc=igb,dc=uiuc,dc=edu
filter
That did it, thanks everyone,
Dan
On Thu, 2004-11-04 at 12:49, Alan DeKok wrote:
I uncommented and did appropriate changes (below) to the ldap section of
the modules area. What else needs done? I am deleting the commented
lines.
Un-comment other references to ldap in radiusd.conf.
I arrived at the point where I thought it would be a good idea to go
ahead and purchase a certifcate for my radius server rather than just
using myself as the authority, and I somehow botched it and radius will
not work. I have my guess as to what I did wrong, but to be sure can
anyone fire back
I have a working freeradius system that is logging the hardware
addresses of the users as they successfully connect through the system.
I would like to also match the userid to the hardware address, and try
as I might I cannot really figure/find out how to do that. Can someone
show me the way or
16 matches
Mail list logo
