Hi All,
I am new in pulseaudio and currently using pulseaudio8.0. I am doing
HeadSet to DMIC switching but lacking in few rules.
Question:-
While switching endpoints, pulseaudio will close already open Stream
related to one endpoint and will open stream related to another endpoint?
Or same strea
Disable presently active device and enable other
device*
> Are you using UCM?
>
*Yes*
Headset and DMIC are different devices in alsa.
On Thu, Sep 15, 2016 at 9:14 PM, Tanu Kaskinen wrote:
> On Wed, 2016-09-14 at 16:42 +0530, Nishit Sharma wrote:
> > Hi All,
> >
> &g
Hi All,
I have observed strange behavior of PulseAudio8.0 which is as:-
I have one card which have 2 devices AMIC and DMIC. I am using ALSA, UCM
config files with PulseAudio. Before pulseaudio boots up Headset and DMIC
have been connected on card. When PulseAudio boots up it initializes AMIC (
Hea
Please find the reply below:-
On Sun, Sep 18, 2016 at 5:19 PM, Tanu Kaskinen wrote:
> On Sat, 2016-09-17 at 17:51 +0530, Nishit Sharma wrote:
> > Hi All,
> >
> > I have observed strange behavior of PulseAudio8.0 which is as:-
> > I have one card which have 2 device
Hi,
Please find attached UCM file meant for Headset and DMIC. Right now i am
unable to give you pactl list as my target board is off which i can't
access.
Regards
On Sun, Sep 18, 2016 at 5:08 PM, Tanu Kaskinen wrote:
> On Thu, 2016-09-15 at 21:37 +0530, Nishit Sharma wrote:
&
>
>
>> When PulseAudio boots up it initializes AMIC (
>
> Headset ) only and i can record using it.
>
> Now, the problem starts. When i plugged Headset the Port switching done
>
> from AMIC to DMIC and after sometime i got overrun without recording
>
> anything.
>
>
>> You seem to be saying tha
Hi All,
In my setup i am facing issues:-
Initially Speaker is on and file played can be heard from Speaker, Now when
headset/headphone plugged in pulseaudio switches to headset/headphones as
per the UCM config files which is working fine. Problem comes when
switching from headphones/headset to spe
uence [
cdev "hw:broxtonrt298"
exec "echo HiFi Headphones EnableSequnece"
cset "name='HPO L Switch' 1"
cset "name='HPO R Switch' 1"
cset "name='Headphone Jack Switch' 1"
cset "name='Speaker Playback Switch' 0,0&quo
ay and both level were same.
Is pulseaudio internally raises volume in case of Playback???
Regards
Nishit
>
> On Wed, Dec 7, 2016 at 6:05 PM, Tanu Kaskinen wrote:
>
>> On Wed, 2016-12-07 at 17:09 +0530, Nishit Sharma wrote:
>> > Hi All,
>> >
>> > In my se
On Thu, Dec 8, 2016 at 3:37 PM, Tanu Kaskinen wrote:
> On Thu, 2016-12-08 at 15:28 +0530, Nishit Sharma wrote:
> > Hi All,
> >
> > I am facing noise issues when playing through Speaker/Headphone using
> > pulseaduio and UCM config files but this is not happening in cas
Hi,
I have checked the sink volume using commands provided and it was 450%. Set
the volume to 100% and now speaker/headet playing smooth.
Thanks for support.
Regards
Nishit Sharma
On Sat, Dec 10, 2016 at 7:07 PM, Tanu Kaskinen wrote:
> On Thu, 2016-12-08 at 15:43 +0530, Nishit Sharma wr
11 matches
Mail list logo