Anyone have a copy of an older version of the code user tables? I
have chip version rev 4.34, and the RB sites text is rev 4.7.. There
are some differences apparently and it would be nice to get the
correct tables.
Randy
The Old codes were 3 digits like 100 ,101,102,103
the newer versions had 4 digits 4100,4101,4102 Ect..
try that
--- On Wed, 12/17/08, wb8art wb8...@netzero.net wrote:
From: wb8art wb8...@netzero.net
Subject: [Repeater-Builder] RC 1000 controller code table
To: Repeater-Builder
Our club has a Maggiore Hi-Pro repeater with an RC-1000 controller.
Question: I have the RC-1000 manual, version 4.3 dated July 1, 1995.
It escapes me how to access the controller via DTMF to do some
changes. I am confused what the A and D control and user codes are.
1. I want to be able to
-Builder] RC-1000 Controller question
Our club has a Maggiore Hi-Pro repeater with an RC-1000 controller.
Question: I have the RC-1000 manual, version 4.3 dated July 1, 1995.
It escapes me how to access the controller via DTMF to do some
changes. I am confused what the A and D control
Nate, the RC-1000 is programmed by opening the controller for
programming input by sending two code sequences. The unlock sequence
has a 'D' prefix hard wired and can't be changed as I recall, with two
additional characters. A typical sequence would be something like 'D7B'
and D7C'. The
Access to the AXX and DXX control codes can be enabled or disabled
with two
control codes; Control Code enable and Control Code disable. When
disabled the
only control code to function is the Control Code Enable. These codes
do NOT
affect access to the * and # user codes.
The above
: Thursday, May 11, 2006 1:13 AM
Subject: [Repeater-Builder] RC-1000 Controller question
Our club has a Maggiore Hi-Pro repeater with an RC-1000 controller.
Question: I have the RC-1000 manual, version 4.3 dated July 1, 1995.
It escapes me how to access the controller via DTMF to do some
ch
When I program a function for example DTMF Muting enable/disable or
Tail beep program
Then disable controler codes all is OK but if I loss power it
reverts back to previous setting
This happens on new changes leading me to think I am missing a step
to save them. All others seem OK
VA3VKK
Kim
The Ron Wright RC1000 is a little tricky. Make sure you have the
correct Control Program Select Code List (Table 15.1) for the Revision of
your controller. You should use the table that is in the book that came
with the controller. They are all different. I have a number of these RC1000
]
www.orlg.org
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]
Sent: Sunday, March 13, 2005 10:54
AM
To: Repeater-Builder@yahoogroups.com
Subject: Re: [Repeater-Builder] RC
1000 Controller
The Ron
Wright RC1000 is a little tricky. Make sure you have the correct Control
. It is unlikely though, as they
are pretty bullet proof.
Richard, N7TGB
-Original Message-
From: va3vkk [mailto:[EMAIL PROTECTED]
Sent: Sunday, March 13, 2005 10:28 AM
To: Repeater-Builder@yahoogroups.com
Subject: [Repeater-Builder] RC 1000 Controller
When I program a function
ReRC1000..I experienced same problem you mentioned about it accepts
the instruction by giving RR but it really didn't. I call the controller
the fortune cookie controller because it lies to me by saying it accepted the
code but it really didn't. First off, don't be afraid to do a reset
RC-1000 Controller by Micro Computer Concepts
Unable to gain access after I enabled the programing control 1 2
made my adjustments.
Disabled program control.
The controller acepted the changes.
When it came time to disable access I could not get a response.
I am out of programing mode for sure.
PROTECTED]
To: Repeater-Builder@yahoogroups.com
Sent: Sunday, November 16, 2003 8:26 AM
Subject: [Repeater-Builder] RC-1000 Controller
| RC-1000 Controller by Micro Computer Concepts
| Unable to gain access after I enabled the programing control 1 2
|
Your use of Yahoo! Groups is subject
Subject: Re: [Repeater-Builder] RC-1000 Controller
on programming commands with an D like D14 to enable programming the cwid,
do not enter the D.
Also commands with #, like #9 to force ID, enter 09 and do not enter #.
Had the same challange last Thursday. Once programmed really works
well
15 matches
Mail list logo
