>> I have many times. The trick is to use distilled ozonated SPRING water.
>>The Spring water is what does it and I think it is because it has a mineral
>>that doesn't distill out.
>> I cook for 20 minutes using a device that I built. If your interested in
>>the plans let me know and I'll send them.
>>
>>Reid
>>Distilled ozonated Spring water...what is the name brand and where did you
>get it? I have found ozonated distilled water, but never what you have
>mentioned above. What is the ppm that you have come to? and what type of
>device are you using?
>Donna Earnest
The name brand it Spring Dale Distilled Water and I've been getting it
at Krogers. There address is Clearidage Springs, Waverly Tennessee, 37185.
The ppm that I was getting when I was making it was 20 and it takes,
if I remember right, 15 minutes. Here's the device plans.
============================================================================
========
Parts list:
==FOR
TIMMER=========================================================================
* RS = Radio Shack
1: 10 megohm resistors (RS #271-1365 5 in a pack) $ .49
2: 1 non polar .01 cap (RS #272-1065 2 in a pack) $ .59
3: Standard 555 timmer (don't use TLC version had a bad one) $?.?? Couldn't
find part# 4: 1 5vdc reed relay (RS #275-232 1 in a pack) $2.49
5: 2 silicon Diodes (RS #276-1103 2 in a pack) $ .79
6: 1 10mfd elec. Cap (RS #272-1025 1 in a pack) $ .59
7: 1 Enginers Mini-notebook (RS #276-5010a Book) $1.59
In place of R1 on the circuit right now I have 5 10megohm 1/4 watt resistors
(part 271-1365) and the timming is 15 minutes. I haven't had the time to remove
one and test to see if it drops down to 10 minutes yet. Every thing else is
the same. The circuit is on page 9 (timmer plus relay).
Just removed one and the time fell to 9 minutes. That should produce around
18ppm. I'll probally leave all 5 in there and let it run for 15 minutes
insted of 10 to get the ppm up around 30-35.
The circuit is on page 9 called Timmer Plus relay.
====FOR CS BOX
=======================================================================
* RS = Radio Shack
1: Transformer (RS #273-1366a 110v -> 25v AC 480ma) $6.00
2: Getting Started in Electronics (RS #276-5003 Page 102) $2.00
3: 3 Diodes (RS #276-1103) $2.00
4: 3 Capacitors (RS #272-1014) $3.00
5: Circuit Board (RS #276-148A) $2.00
6: 2 Gator Clips $2.00
7: Cheep Extention cord $1.00
8: Baking soda $1.00
9: Distilled and ozonated water $1.00
10: Silver rods .999 or better (.9999 are the best) $10.00
11: Glass 2 1/2 inches wide 5 1/2 inches tall (Walmart) ??.??
12: Scotch brite (plastic) scrubber (walmart) 1.00
=======================================================================
* In my project I used 3 capacitors and 3 diodes from an old
circuit board. The Caps were 10uf 50v and the diodes unknown.
The caps listed are the equal.
The distilled water can be purchased from:
Anita Spring water Co.
3899 Produce Rd.
Louisville, Ky. 40218
Phone: 502-969-4500
SpringDale Distilled Water Purple label and found at Krogers.
(makes the golden silver) (spring water)
Distributed by
Inter-American Foods, INC.
Cincinnati, Ohio 45202
Made by Clearidge Springs
Waverly, Tennessee 37185
Or your local store just remember ozonated and spring water.
----------------------------------------------------------------------
The silver rods can be purchased from:
SOTA Intruments Incorporated
P.O. Box 26161, Central Postal Station,
Richmond, BC, V6Y 3V3 Canada
1-800-224-0242
($25 with plugin)
Questions on pricing of silver rods send SASE to: ($10 I think)
Send a stampted self adressed envelope to for more info:
(NOTE .9999 rods insted of .999) ($10)
Jay Schomer
227 Rosebay Dr.
Encinitas, Ca 92024
HAUSER & MILLER CO.
10950 Lin-Valle Dr, St
Louis, MO, 63123.
Tel 1-800-462-7447,
Fax: 314-487-0394.
(.999 $25 min. order)
12 gauge wire
----------------------------------------------------------------------
NOTES: There are three wires on one side of the transformer
(2 yellow - 1 black) and two on the other side (2 black).
The 2 black go to 110v AC (cut drop cord) and the two
yellow go to the voltage tripler.
The single black isn't connected or used.
Cut the female end off the cheep extention cord (7) so that
the plugin and wire are left. Strip and solder the end of the
extention cord ends to the two black wires on the transformer.
Tape or in close the solder joints so their not exposed.
VERY IMPORTANT!!! COVER THOSE SOLDER JOINTS! They are 110v AC
and could be deadly if touched and even worse if wet and
touched!
Another good way to do this is before soldering cut a small
1 inch long piece of a plastic straw and slip it over the
wires. When done soldering pull the straw over the solder
joints then use a hot glue gun to fill the straw.
Build the circuit "Voltage Tripler" page 102 of the book (2).
NOTE: The silver lines on the diodes go the same way as the
line side at the point of the triange on the diagram.
The ->->-> on the capacitors goes to the negitive
this is the metal end on the capacitor.
Connect the two yellow wires on the other side of the
transformer to the circuit labeled ( INPUT (Vin) ).
You'll need two short pieces of stranded wire to connect
circuit the OUTPUT (3 Vin) to the two gator clips. I used
a small length of the drop cord.
Solder one end of the wire to the OUTPUT (3 Vin) and Solder
2 of the gator clips to the other end of those wires.
Plug in the transformer and test the voltage at the + and -
ends of the circuit labled OUTPUT (3 Vin) in the book. You
should have 75v DC.
To make the baking soda solution add 1/8 teaspoon of baking soda
to 8oz of distilled water in a REAL clean glass (see cleaning
instructions below). Don't ever stir it just swirl it around until
all the soda is mixed. The best thing to do is to poor that solution
into some kind of bottle that has an eye dropper. It should allways
be kept in a closed container. Shake before using. NEVER stir anything
allways swirl (swish) it around. Spoons, plastics, anything added
to the water haave microscopic materials on it and will effect the
making and ppm of the Colloidal Silver.
Clean the glass real good then with Boiling water rinse it out.
Dry it first with a real clean cloth. Rinse it once or tiwce with a
small amount of distilled water. It's REAL important to get the glass
very clean. You don't want anything else in there but the distilled
water and solution (electrolite).
Clean the silver rods brite with a scotch brite plastic scrubber.
Then rinse them real good with distilled water. NEVER use steel wool
or anything else but the plastic scrubber. Steel wool has metal particals
in it that will penitrate the silver rods. You don't want anything in the
glass except the baking soda solution, silver rods, and the distilled
water.
Shake the baking soda solution first. Then put one drop of the
solution in the clean glass. Now add 8oz of the distilled water. At
first I used a measuring cup to measure the 8oz. Then poored it into
the glass. I then took a piece of black tape and made a line at the
level of the water. This eliminates the need for the measuring cup.
Clip the gator clips to the rods and insert them into the glass
1/2 inch apart. The rods should be about 3 inches long and put about
2 inches of the rods in the solution NEVER LET THE CLIPS TOUCH THE
WATER. Also never let the rods rest on the bottom or the side of the
glass this will cause large particals to break off the rods. Also after
the mixture is done let it sit over night. I cover mine with a plastic
glass to keep out the light.
Plug in the device. At first you won't notice any thing. Then you'll
start to see small bubbles comming off the rods. Then a cloud of white
or brownish looking smoke in the water. Every 2 minutes stop and swirl
the water around. After 10 minutes unplug the device and remove the
silver rods.
You should remove the mixture from the glass that you have it
in, if you don't it might stain it gold in color. The next time you
make a mixture swap the rods so that you'll get equal deteration of
the rods. You've now got Colliodal Silver but you still need to
filter it some how. You can start with a coffee filter or a paper
towel as you poor the solution from the making glass to the container
that your going to keep it in. The container should be light proof
or real dark. A good "clean" peroxide bottle works good.
It should be stable for about 1 week but more testing needs to
be done to verify that.
----------------------------------------------------------------------
Other things I plan to add to the project is a 555 push button
timmer circuit, a fan or something to stir the solution as it makes,
and put it all in a project box with a plugin for the silver circuit.
This way I can also add a beck (or bare) plugin device using
the 25v transformer.
Other tests needed:
A partical size test needs to be ran!
If the particals are too large then lower the voltage or increase
the distance of the rods.
Heating the solution first to see if that drives up the ppm.
A little more soda solution to see if 5 minutes works as fast.
Last test that I can afford is going to be for ppm for what I
have now to see if they are around 40 ppm. My last one was 80
at 20 minutes.
If anyone builds this and decides to do more testing please let me
know the results.
Another thing that I've found is making the CS without any additives
MIGHT give you the golden CS effect BUT there's a simpler way and better
way. If you noticed I listed two manufactures of distilled water. To get
the golden silver (tindael Effect) use Distilled natural SPRING water..
The object is to make the same stuff each time. The length the rods
are inserted into the glass, the width apart, the temp. of the solution,
the amount of electrolite, the amount of electrolite and distilled water
mixed, the time that it's cooked, and the voltage are equal the ppm plus
the partical size.
When using no electrolite, just distilled water and 30 minutes of
cooking the solution will start to turn black at the top then progress
to the bottom of the glass. The reason for this I think is the solution
is becoming more conductive. It is so much conductive at this point that
the particals inside the solution are BURNING from the electricity flow.
(IE silver oxide)
Allways filter the mixture with 2-3 coffee filters when done!!
============================================================================
=====
