ls /lib/modules/2.6.37.6-smp/kernel/drivers/net/wireless/rtl818x/rtl8187.ko
Parece que esse módulo não existe. On Wed, Nov 23, 2011 at 10:40 PM, joseph <[email protected]> wrote: > bash-4.1# > bash-4.1# cat /etc/slackware-version > Slackware 13.37.0 > bash-4.1# > bash-4.1# > bash-4.1# > bash-4.1# uname -a > Linux Jose-notebook 2.6.37.6-smp #2 SMP Sat Apr 9 23:39:07 CDT 2011 i686 > Pentium(R) Dual-Core CPU T4200 @ 2.00GHz GenuineIntel GNU/Linux > bash-4.1# > > > > > Em 23-11-2011 21:35, Ellington Santos escreveu: > > Bom, vc não tem o módulo rtl8187. > > > Mais dois comandos: > > > cat /etc/slackware-version > uname -a > > > > > On Wed, Nov 23, 2011 at 9:56 PM, joseph <[email protected]> wrote: > > bash-4.1# modprobe rtl8187 > FATAL: Module rtl8187 not found. > > bash-4.1# ifconfig -a > eth0 Link encap:Ethernet HWaddr 00:E0:4C:68:07:77 > inet addr:192.168.1.100 Bcast:255.255.255.255 Mask:255.255.255.0 > UP BROADCAST RUNNING MULTICAST MTU:576 Metric:1 > RX packets:23281 errors:0 dropped:0 overruns:0 frame:0 > TX packets:15753 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:9782409 (9.3 Mb) TX bytes:2147564 (2.0 Mb) > Interrupt:41 Base address:0x8000 > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 Scope:Host > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:37 errors:0 dropped:0 overruns:0 frame:0 > TX packets:37 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:1931 (1.8 Kb) TX bytes:1931 (1.8 Kb) > > bash-4.1# > bash-4.1# > bash-4.1# dmesg | tail > [ 30.652559] NET: Registered protocol family 10 > [ 30.652914] lo: Disabled Privacy Extensions > [ 41.737875] NET: Registered protocol family 5 > [ 916.490077] [drm:intel_panel_get_max_backlight] *ERROR* fixme: max PWM is > zero. > [ 1689.232901] [drm:intel_panel_get_max_backlight] *ERROR* fixme: max PWM is > zero. > [ 1689.232906] [drm:intel_panel_get_max_backlight] *ERROR* fixme: max PWM is > zero. > [ 2008.814857] [drm:intel_panel_get_max_backlight] *ERROR* fixme: max PWM is > zero. > [ 2008.837027] [drm:intel_panel_get_max_backlight] *ERROR* fixme: max PWM is > zero. > [ 2279.237240] [drm:intel_panel_get_max_backlight] *ERROR* fixme: max PWM is > zero. > [ 2279.237246] [drm:intel_panel_get_max_backlight] *ERROR* fixme: max PWM is > zero. > bash-4.1# > bash-4.1# > bash-4.1# > bash-4.1# tail /var/log/messages > Nov 23 21:19:16 Jose-notebook blueman-mechanism: loading Ppp > Nov 23 21:19:16 Jose-notebook blueman-mechanism: loading Network > Nov 23 21:19:16 Jose-notebook blueman-mechanism: loading Config > Nov 23 21:19:46 Jose-notebook blueman-mechanism: Exiting > Nov 23 21:30:58 Jose-notebook -- MARK -- > Nov 23 21:50:58 Jose-notebook -- MARK -- > Nov 23 21:51:05 Jose-notebook dhcpcd[1783]: eth0: renewing lease of > 192.168.1.100 > Nov 23 21:51:05 Jose-notebook dhcpcd[1783]: eth0: acknowledged 192.168.1.100 > from 192.168.1.1 `�' > Nov 23 21:51:05 Jose-notebook dhcpcd[1783]: eth0: leased 192.168.1.100 for > 7200 seconds > Nov 23 21:51:05 Jose-notebook dhcpcd[3325]: eth0: eth0: MTU set to 576 > bash-4.1# > > > > Em 23-11-2011 20:53, Ellington Santos escreveu: > > Então seu hardware é detectado, mas o módulo não subiu com sucesso. > > Tente um modprobe rtl8187 > Cole aqui a saida dos comandos abaixo logo após tentar carregar o módulo: > > ifconfig -a > dmesg | tail > tail /var/log/messages > > > > On Wed, Nov 23, 2011 at 9:47 PM, joseph <[email protected]> wrote: > > bash-4.1# ifconfig -a > eth0 Link encap:Ethernet HWaddr 00:E0:4C:68:07:77 > inet addr:192.168.1.100 Bcast:255.255.255.255 Mask:255.255.255.0 > UP BROADCAST RUNNING MULTICAST MTU:576 Metric:1 > RX packets:20348 errors:0 dropped:0 overruns:0 frame:0 > TX packets:13474 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:8998639 (8.5 Mb) TX bytes:1745824 (1.6 Mb) > Interrupt:41 Base address:0x8000 > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 Scope:Host > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:37 errors:0 dropped:0 overruns:0 frame:0 > TX packets:37 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:1931 (1.8 Kb) TX bytes:1931 (1.8 Kb) > > bash-4.1# > bash-4.1# > bash-4.1# > bash-4.1# lsmod > Module Size Used by > snd_seq_dummy 1119 0 > snd_seq_oss 25900 0 > snd_seq_midi_event 4696 1 snd_seq_oss > snd_seq 42680 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event > snd_seq_device 4505 3 snd_seq_dummy,snd_seq_oss,snd_seq > snd_pcm_oss 34554 0 > snd_mixer_oss 14726 2 snd_pcm_oss > appletalk 22978 20 > psnap 1545 1 appletalk > llc 2988 1 psnap > ipv6 236629 24 > pcmcia 32618 0 > pcmcia_core 10169 1 pcmcia > cpufreq_ondemand 7672 2 > speedstep_lib 2663 0 > acpi_cpufreq 5195 1 > freq_table 2039 2 cpufreq_ondemand,acpi_cpufreq > mperf 923 1 acpi_cpufreq > plip 11167 0 > lp 7105 0 > ppdev 4901 0 > parport_pc 18218 0 > parport 25627 4 plip,lp,ppdev,parport_pc > fuse 58136 1 > i915 360914 2 > uvcvideo 55980 0 > drm_kms_helper 23927 1 i915 > drm 143170 3 i915,drm_kms_helper > videodev 57461 1 uvcvideo > v4l1_compat 13666 2 uvcvideo,videodev > i2c_algo_bit 4287 1 i915 > joydev 7695 0 > r8169 32377 0 > intel_agp 9000 1 i915 > intel_gtt 11414 3 i915,intel_agp > i2c_i801 7018 0 > rtc_cmos 7970 0 > rtc_core 11871 1 rtc_cmos > video 10482 1 i915 > processor 23158 3 acpi_cpufreq > agpgart 23062 3 drm,intel_agp,intel_gtt > snd_hda_codec_hdmi 20152 1 > mii 3334 1 r8169 > thermal 6718 0 > thermal_sys 11426 3 video,processor,thermal > i2c_core 16421 6 > i915,drm_kms_helper,drm,videodev,i2c_algo_bit,i2c_i801 > output 1456 1 video > rtc_lib 1502 1 rtc_core > sparse_keymap 2436 0 > snd_hda_codec_realtek 222970 1 > shpchp 23205 0 > wmi 7129 0 > evdev 7303 17 > battery 8431 0 > sg 21511 0 > hwmon 1065 1 thermal_sys > snd_hda_intel 18443 2 > psmouse 40986 0 > serio_raw 3542 0 > snd_hda_codec 61720 3 > snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel > snd_hwdep 4772 1 snd_hda_codec > snd_pcm 59843 4 > snd_pcm_oss,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec > snd_timer 15717 2 snd_seq,snd_pcm > snd 43891 14 > snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer > soundcore 4641 2 snd > snd_page_alloc 5925 2 snd_hda_intel,snd_pcm > button 4005 1 i915 > ac 2465 0 > bash-4.1# > bash-4.1# > bash-4.1# > bash-4.1# lspci > 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory > Controller Hub (rev 09) > 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset > Integrated Graphics Controller (rev 09) > 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset > Integrated Graphics Controller (rev 09) > 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI > Controller #4 (rev 03) > 00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI > Controller #5 (rev 03) > 00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI > Controller #6 (rev 03) > 00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI > Controller #2 (rev 03) > 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio > Controller (rev 03) > 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port > 1 (rev 03) > 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port > 2 (rev 03) > 00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port > 3 (rev 03) > 00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port > 6 (rev 03) > 00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI > Controller #1 (rev 03) > 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI > Controller #2 (rev 03) > 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI > Controller #3 (rev 03) > 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI > Controller #1 (rev 03) > 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) > 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev > 03) > 00:1f.2 IDE interface: Intel Corporation ICH9M/M-E 2 port SATA IDE > Controller (rev 03) > 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev > 03) > 00:1f.5 IDE interface: Intel Corporation ICH9M/M-E 2 port SATA IDE > Controller (rev 03) > 08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B > PCI Express Gigabit Ethernet controller (rev 03) > bash-4.1# > bash-4.1# > bash-4.1# > bash-4.1# > bash-4.1# lsusb > Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 001 Device 002: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 > multicard reader > Bus 002 Device 002: ID 0bda:8189 Realtek Semiconductor Corp. RTL8187B > Wireless 802.11g 54Mbps Network Adapter > Bus 002 Device 003: ID 058f:3831 Alcor Micro Corp. > bash-4.1# > bash-4.1# > bash-4.1# > bash-4.1# > > > > > > > Em 22-11-2011 07:39, Ellington Santos escreveu: > > Joseph, > > Primeiramente você precisa saber se sua placa foi detectada. Vamos > verificar a pilha de detecção de forma reversa. Execute os comandos > abaixo como root. Caso algum deles seja bem sucedido, os demais não > precisam ser executados: > > > 1) Camada de userspace: > ifconfig -a > Verifique se o dispositivo wlan0 está na lista. > > 2) Camada de kernelspace: > lsmod > Verifique se o módulo rtl8187 está na lista. > > 3) Camada de hardware: > lspci ou lsusb (depende do seu dispositivo) > Verifique se o hardware aparece na lista. > > > Se o (1) já funcionar, quer dizer que seu dispositivo já está pronto > para o uso. Basta configurar manualmente a rede ou instalar o wicd da > pasta Extra do DVD de instalação do Slackware. Mais instruções no > arquivo README.SLACKWARE na mesma pasta do pacote. > > Se você chegar ao (2) ou (3), envie o arquivo /var/log/messages e a > saída do comando dmesg como anexo. > > Att, > > Ellington Santos (aka necropresto) > > > 2011/11/22 joseph<[email protected]>: > > Olá boa noite a todos, > então instalei o slackware 13.37 porem não consegui configurar minha > wireless. > eu estou com um notebook sti is 1412 e o modelo da placa é REDE WIRELESS > RTL8187B > > " > bash-4.1# lshw -class system > jose-notebook > description: Notebook > product: IS 1412 () > vendor: Semp Toshiba > version: 20ga& ICH9M Chipset > serial: 091025537 > width: 32 bits > capabilities: smbios-2.5 dmi-2.5 smp-1.4 smp > configuration: administrator_password=disabled boot=normal > chassis=notebook cpus=2 frontpanel_password=unknown > keyboard_password=unknown power-on_password=disabled > *-remoteaccess UNCLAIMED > vendor: Intel > physical id: 2 > capabilities: outbound > bash-4.1# > " > > -- > Atenciosamente, > > José Miranda > Assessor de TI > Semana da Engenharia 2012 > www.semanadaeng.com.br > skype: joseph.inf > telefone: (27) 9867-2303 > Engenharia da Computação - UFES > > - - > > Seja livre, use GNU/Linux! > Open Source - Milhares de mentes abertas não podem estar enganadas! > -- > > -- > GUS-BR - Grupo de Usuários de Slackware Brasil > http://www.slackwarebrasil.org/ > http://groups.google.com/group/slack-users-br > > Antes de perguntar: > http://www.istf.com.br/perguntas/ > > Para sair da lista envie um e-mail para: > [email protected] > > -- > Atenciosamente, > > José Miranda > Assessor de TI > Semana da Engenharia 2012 > www.semanadaeng.com.br > skype: joseph.inf > telefone: (27) 9867-2303 > Engenharia da Computação - UFES > > - - > > Seja livre, use GNU/Linux! > Open Source - Milhares de mentes abertas não podem estar enganadas! > -- > > -- > GUS-BR - Grupo de Usuários de Slackware Brasil > http://www.slackwarebrasil.org/ > http://groups.google.com/group/slack-users-br > > Antes de perguntar: > http://www.istf.com.br/perguntas/ > > Para sair da lista envie um e-mail para: > [email protected] > > > -- > Atenciosamente, > > José Miranda > Assessor de TI > Semana da Engenharia 2012 > www.semanadaeng.com.br > skype: joseph.inf > telefone: (27) 9867-2303 > Engenharia da Computação - UFES > > - - > > Seja livre, use GNU/Linux! > Open Source - Milhares de mentes abertas não podem estar enganadas! > -- > > -- > GUS-BR - Grupo de Usuários de Slackware Brasil > http://www.slackwarebrasil.org/ > http://groups.google.com/group/slack-users-br > > Antes de perguntar: > http://www.istf.com.br/perguntas/ > > Para sair da lista envie um e-mail para: > [email protected] > > > -- > Atenciosamente, > > José Miranda > Assessor de TI > Semana da Engenharia 2012 > www.semanadaeng.com.br > skype: joseph.inf > telefone: (27) 9867-2303 > Engenharia da Computação - UFES > > - - > > Seja livre, use GNU/Linux! > Open Source - Milhares de mentes abertas não podem estar enganadas! > -- > > -- > GUS-BR - Grupo de Usuários de Slackware Brasil > http://www.slackwarebrasil.org/ > http://groups.google.com/group/slack-users-br > > Antes de perguntar: > http://www.istf.com.br/perguntas/ > > Para sair da lista envie um e-mail para: > [email protected] -- GUS-BR - Grupo de Usuários de Slackware Brasil http://www.slackwarebrasil.org/ http://groups.google.com/group/slack-users-br Antes de perguntar: http://www.istf.com.br/perguntas/ Para sair da lista envie um e-mail para: [email protected]
