Re: [slack-users] rede sem fio

Wed, 23 Nov 2011 16:10:57 -0800 

reconheceu!!!!!!!!!!!!!

ash-4.1#
bash-4.1#
bash-4.1# modprobe rtl8187
bash-4.1#
bash-4.1#
bash-4.1# modprobe rtl8187
bash-4.1# ifconfig -a
eth0      Link encap:Ethernet  HWaddr 00:E0:4C:68:07:77
inet addr:192.168.1.100 Bcast:255.255.255.255 Mask:255.255.255.0 
          UP BROADCAST RUNNING MULTICAST  MTU:576  Metric:1
          RX packets:211938 errors:0 dropped:0 overruns:0 frame:0
          TX packets:138724 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:112225592 (107.0 Mb)  TX bytes:13122973 (12.5 Mb)
          Interrupt:41 Base address:0x8000

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:37 errors:0 dropped:0 overruns:0 frame:0
          TX packets:37 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:1931 (1.8 Kb)  TX bytes:1931 (1.8 Kb)

wlan0     Link encap:Ethernet  HWaddr 00:17:C4:AC:98:77
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

bash-4.1#
bash-4.1# dmesg | tail
[ 8291.115965] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) 
[ 8291.347207] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 8291.347532] ieee80211 phy0: hwaddr 00:17:c4:ac:98:77, RTL8187BvE V0 + rtl8225z2, rfkill mask 2 
[ 8291.371457] rtl8187: Customer ID is 0x00
[ 8291.371687] Registered led device: rtl8187-phy0::radio
[ 8291.371911] Registered led device: rtl8187-phy0::tx
[ 8291.373786] Registered led device: rtl8187-phy0::rx
[ 8291.374572] rtl8187: wireless switch is on
[ 8291.375689] usbcore: registered new interface driver rtl8187
[ 8295.224749] ADDRCONF(NETDEV_UP): wlan0: link is not ready
bash-4.1#
bash-4.1#
bash-4.1#
bash-4.1# tail /var/log/messages
Nov 23 23:08:46 Jose-notebook kernel: [ 8291.115960] (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Nov 23 23:08:46 Jose-notebook kernel: [ 8291.115962] (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Nov 23 23:08:46 Jose-notebook kernel: [ 8291.115965] (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Nov 23 23:08:47 Jose-notebook kernel: [ 8291.347532] ieee80211 phy0: hwaddr 00:17:c4:ac:98:77, RTL8187BvE V0 + rtl8225z2, rfkill mask 2 Nov 23 23:08:47 Jose-notebook kernel: [ 8291.371457] rtl8187: Customer ID is 0x00 Nov 23 23:08:47 Jose-notebook kernel: [ 8291.374572] rtl8187: wireless switch is on Nov 23 23:08:47 Jose-notebook kernel: [ 8291.375689] usbcore: registered new interface driver rtl8187 Nov 23 23:08:50 Jose-notebook kernel: [ 8295.224749] ADDRCONF(NETDEV_UP): wlan0: link is not ready Nov 23 23:08:54 Jose-notebook logger: /etc/rc.d/rc.inet1: /sbin/iwconfig wlan0 nick Jose-notebook Nov 23 23:08:54 Jose-notebook logger: /etc/rc.d/rc.inet1: /sbin/iwconfig wlan0 essid "any" 
bash-4.1#
bash-4.1#



Em 23-11-2011 22:03, Ellington Santos escreveu:

Esse arquivo deveria existir. Creio q o pacote
modules-smp-2.6.37.6_smp-i686-2.txz que você instalou estava
corrompido.



wget 
ftp://ftp.osuosl.org/pub/slackware/slackware-13.37/slackware/a/kernel-modules-smp-2.6.37.6_smp-i686-2.txz
installpkg kernel-modules-smp-2.6.37.6_smp-i686-2.txz
modprobe rtl8187
ifconfig -a
dmesg | tail
tail /var/log/messages




On Wed, Nov 23, 2011 at 10:59 PM, joseph<[email protected]>  wrote:

bash-4.1#
bash-4.1#
bash-4.1#
bash-4.1# ls
/lib/modules/2.6.37.6-smp/kernel/drivers/net/wireless/rtl818x/rtl8187.ko
ls: impossível acessar
/lib/modules/2.6.37.6-smp/kernel/drivers/net/wireless/rtl818x/rtl8187.ko:
Arquivo ou diretório não encontrado
bash-4.1#
bash-4.1#
bash-4.1#
bash-4.1#
bash-4.1# ls
/lib/modules/2.6.37.6-smp/kernel/drivers/net/wireless/rtl818x/rtl8187.ko
ls: impossível acessar
/lib/modules/2.6.37.6-smp/kernel/drivers/net/wireless/rtl818x/rtl8187.ko:
Arquivo ou diretório não encontrado
bash-4.1#
bash-4.1#
bash-4.1#



Em 23-11-2011 21:58, Ellington Santos escreveu:

ls /lib/modules/2.6.37.6-smp/kernel/drivers/net/wireless/rtl818x/rtl8187.ko

Parece que esse módulo não existe.


On Wed, Nov 23, 2011 at 10:40 PM, joseph<[email protected]>  wrote:

bash-4.1#
bash-4.1# cat /etc/slackware-version
Slackware 13.37.0
bash-4.1#
bash-4.1#
bash-4.1#
bash-4.1# uname -a
Linux Jose-notebook 2.6.37.6-smp #2 SMP Sat Apr 9 23:39:07 CDT 2011 i686
Pentium(R) Dual-Core CPU       T4200  @ 2.00GHz GenuineIntel GNU/Linux
bash-4.1#




Em 23-11-2011 21:35, Ellington Santos escreveu:

Bom, vc não tem o módulo rtl8187.


Mais dois comandos:


cat /etc/slackware-version
uname -a




On Wed, Nov 23, 2011 at 9:56 PM, joseph<[email protected]>  wrote:

bash-4.1# modprobe rtl8187
FATAL: Module rtl8187 not found.

bash-4.1# ifconfig -a
eth0      Link encap:Ethernet  HWaddr 00:E0:4C:68:07:77
           inet addr:192.168.1.100  Bcast:255.255.255.255  Mask:255.255.255.0
           UP BROADCAST RUNNING MULTICAST  MTU:576  Metric:1
           RX packets:23281 errors:0 dropped:0 overruns:0 frame:0
           TX packets:15753 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:9782409 (9.3 Mb)  TX bytes:2147564 (2.0 Mb)
           Interrupt:41 Base address:0x8000

lo        Link encap:Local Loopback
           inet addr:127.0.0.1  Mask:255.0.0.0
           inet6 addr: ::1/128 Scope:Host
           UP LOOPBACK RUNNING  MTU:16436  Metric:1
           RX packets:37 errors:0 dropped:0 overruns:0 frame:0
           TX packets:37 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:0
           RX bytes:1931 (1.8 Kb)  TX bytes:1931 (1.8 Kb)

bash-4.1#
bash-4.1#
bash-4.1# dmesg | tail
[   30.652559] NET: Registered protocol family 10
[   30.652914] lo: Disabled Privacy Extensions
[   41.737875] NET: Registered protocol family 5
[  916.490077] [drm:intel_panel_get_max_backlight] *ERROR* fixme: max PWM is
zero.
[ 1689.232901] [drm:intel_panel_get_max_backlight] *ERROR* fixme: max PWM is
zero.
[ 1689.232906] [drm:intel_panel_get_max_backlight] *ERROR* fixme: max PWM is
zero.
[ 2008.814857] [drm:intel_panel_get_max_backlight] *ERROR* fixme: max PWM is
zero.
[ 2008.837027] [drm:intel_panel_get_max_backlight] *ERROR* fixme: max PWM is
zero.
[ 2279.237240] [drm:intel_panel_get_max_backlight] *ERROR* fixme: max PWM is
zero.
[ 2279.237246] [drm:intel_panel_get_max_backlight] *ERROR* fixme: max PWM is
zero.
bash-4.1#
bash-4.1#
bash-4.1#
bash-4.1# tail /var/log/messages
Nov 23 21:19:16 Jose-notebook blueman-mechanism: loading Ppp
Nov 23 21:19:16 Jose-notebook blueman-mechanism: loading Network
Nov 23 21:19:16 Jose-notebook blueman-mechanism: loading Config
Nov 23 21:19:46 Jose-notebook blueman-mechanism: Exiting
Nov 23 21:30:58 Jose-notebook -- MARK --
Nov 23 21:50:58 Jose-notebook -- MARK --
Nov 23 21:51:05 Jose-notebook dhcpcd[1783]: eth0: renewing lease of
192.168.1.100
Nov 23 21:51:05 Jose-notebook dhcpcd[1783]: eth0: acknowledged 192.168.1.100
from 192.168.1.1 `�'
Nov 23 21:51:05 Jose-notebook dhcpcd[1783]: eth0: leased 192.168.1.100 for
7200 seconds
Nov 23 21:51:05 Jose-notebook dhcpcd[3325]: eth0: eth0: MTU set to 576
bash-4.1#



Em 23-11-2011 20:53, Ellington Santos escreveu:

Então seu hardware é detectado, mas o módulo não subiu com sucesso.

Tente um modprobe rtl8187
Cole aqui a saida dos comandos abaixo logo após tentar carregar o módulo:

ifconfig -a
dmesg | tail
tail /var/log/messages



On Wed, Nov 23, 2011 at 9:47 PM, joseph<[email protected]>  wrote:

bash-4.1# ifconfig -a
eth0      Link encap:Ethernet  HWaddr 00:E0:4C:68:07:77
          inet addr:192.168.1.100  Bcast:255.255.255.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:576  Metric:1
          RX packets:20348 errors:0 dropped:0 overruns:0 frame:0
          TX packets:13474 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:8998639 (8.5 Mb)  TX bytes:1745824 (1.6 Mb)
          Interrupt:41 Base address:0x8000

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:37 errors:0 dropped:0 overruns:0 frame:0
          TX packets:37 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:1931 (1.8 Kb)  TX bytes:1931 (1.8 Kb)

bash-4.1#
bash-4.1#
bash-4.1#
bash-4.1# lsmod
Module                  Size  Used by
snd_seq_dummy           1119  0
snd_seq_oss            25900  0
snd_seq_midi_event      4696  1 snd_seq_oss
snd_seq                42680  5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event
snd_seq_device          4505  3 snd_seq_dummy,snd_seq_oss,snd_seq
snd_pcm_oss            34554  0
snd_mixer_oss          14726  2 snd_pcm_oss
appletalk              22978  20
psnap                   1545  1 appletalk
llc                     2988  1 psnap
ipv6                  236629  24
pcmcia                 32618  0
pcmcia_core            10169  1 pcmcia
cpufreq_ondemand        7672  2
speedstep_lib           2663  0
acpi_cpufreq            5195  1
freq_table              2039  2 cpufreq_ondemand,acpi_cpufreq
mperf                    923  1 acpi_cpufreq
plip                   11167  0
lp                      7105  0
ppdev                   4901  0
parport_pc             18218  0
parport                25627  4 plip,lp,ppdev,parport_pc
fuse                   58136  1
i915                  360914  2
uvcvideo               55980  0
drm_kms_helper         23927  1 i915
drm                   143170  3 i915,drm_kms_helper
videodev               57461  1 uvcvideo
v4l1_compat            13666  2 uvcvideo,videodev
i2c_algo_bit            4287  1 i915
joydev                  7695  0
r8169                  32377  0
intel_agp               9000  1 i915
intel_gtt              11414  3 i915,intel_agp
i2c_i801                7018  0
rtc_cmos                7970  0
rtc_core               11871  1 rtc_cmos
video                  10482  1 i915
processor              23158  3 acpi_cpufreq
agpgart                23062  3 drm,intel_agp,intel_gtt
snd_hda_codec_hdmi     20152  1
mii                     3334  1 r8169
thermal                 6718  0
thermal_sys            11426  3 video,processor,thermal
i2c_core               16421  6
i915,drm_kms_helper,drm,videodev,i2c_algo_bit,i2c_i801
output                  1456  1 video
rtc_lib                 1502  1 rtc_core
sparse_keymap           2436  0
snd_hda_codec_realtek   222970  1
shpchp                 23205  0
wmi                     7129  0
evdev                   7303  17
battery                 8431  0
sg                     21511  0
hwmon                   1065  1 thermal_sys
snd_hda_intel          18443  2
psmouse                40986  0
serio_raw               3542  0
snd_hda_codec          61720  3
snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel
snd_hwdep               4772  1 snd_hda_codec
snd_pcm                59843  4
snd_pcm_oss,snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec
snd_timer              15717  2 snd_seq,snd_pcm
snd                    43891  14
snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_hda_codec_hdmi,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer
soundcore               4641  2 snd
snd_page_alloc          5925  2 snd_hda_intel,snd_pcm
button                  4005  1 i915
ac                      2465  0
bash-4.1#
bash-4.1#
bash-4.1#
bash-4.1# lspci
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory
Controller Hub (rev 09)
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset
Integrated Graphics Controller (rev 09)
00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset
Integrated Graphics Controller (rev 09)
00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #4 (rev 03)
00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #5 (rev 03)
00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #6 (rev 03)
00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
Controller #2 (rev 03)
00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio
Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port
1 (rev 03)
00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port
2 (rev 03)
00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port
3 (rev 03)
00:1c.5 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port
6 (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #3 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
Controller #1 (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93)
00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev
03)
00:1f.2 IDE interface: Intel Corporation ICH9M/M-E 2 port SATA IDE
Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev
03)
00:1f.5 IDE interface: Intel Corporation ICH9M/M-E 2 port SATA IDE
Controller (rev 03)
08:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B
PCI Express Gigabit Ethernet controller (rev 03)
bash-4.1#
bash-4.1#
bash-4.1#
bash-4.1#
bash-4.1# lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 002: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0
multicard reader
Bus 002 Device 002: ID 0bda:8189 Realtek Semiconductor Corp. RTL8187B
Wireless 802.11g 54Mbps Network Adapter
Bus 002 Device 003: ID 058f:3831 Alcor Micro Corp.
bash-4.1#
bash-4.1#
bash-4.1#
bash-4.1#






Em 22-11-2011 07:39, Ellington Santos escreveu:

Joseph,

Primeiramente você precisa saber se sua placa foi detectada. Vamos
verificar a pilha de detecção de forma reversa. Execute os comandos
abaixo como root. Caso algum deles seja bem sucedido, os demais não
precisam ser executados:


1) Camada de userspace:
        ifconfig -a
     Verifique se o dispositivo wlan0 está na lista.

2) Camada de kernelspace:
         lsmod
     Verifique se o módulo rtl8187 está na lista.

3) Camada de hardware:
         lspci ou lsusb (depende do seu dispositivo)
     Verifique se o hardware aparece na lista.


Se o (1) já funcionar, quer dizer que seu dispositivo já está pronto
para o uso. Basta configurar manualmente a rede ou instalar o wicd da
pasta Extra do DVD de instalação do Slackware. Mais instruções no
arquivo README.SLACKWARE na mesma pasta do pacote.

Se você chegar ao (2) ou (3), envie o arquivo /var/log/messages e a
saída do comando dmesg como anexo.

Att,

Ellington Santos (aka necropresto)


2011/11/22 joseph<[email protected]>:

Olá boa noite a todos,
então instalei o slackware 13.37 porem não consegui configurar minha
wireless.
eu estou com um notebook sti is 1412 e o modelo da placa é REDE WIRELESS
RTL8187B

"
bash-4.1# lshw -class system
jose-notebook
    description: Notebook
    product: IS 1412 ()
    vendor: Semp Toshiba
    version: 20ga&    ICH9M Chipset
    serial: 091025537
    width: 32 bits
    capabilities: smbios-2.5 dmi-2.5 smp-1.4 smp
    configuration: administrator_password=disabled boot=normal
chassis=notebook cpus=2 frontpanel_password=unknown
keyboard_password=unknown power-on_password=disabled
  *-remoteaccess UNCLAIMED
       vendor: Intel
       physical id: 2
       capabilities: outbound
bash-4.1#
"

--
Atenciosamente,

José Miranda
Assessor de TI
Semana da Engenharia 2012
www.semanadaeng.com.br
skype: joseph.inf
telefone: (27) 9867-2303
Engenharia da Computação - UFES

- -

Seja livre, use GNU/Linux!
Open Source  - Milhares de mentes abertas não podem estar enganadas!
--

--
GUS-BR - Grupo de Usuários de Slackware Brasil
http://www.slackwarebrasil.org/
http://groups.google.com/group/slack-users-br

Antes de perguntar:
http://www.istf.com.br/perguntas/

Para sair da lista envie um e-mail para:
[email protected]

--
Atenciosamente,

José Miranda
Assessor de TI
Semana da Engenharia 2012
www.semanadaeng.com.br
skype: joseph.inf
telefone: (27) 9867-2303
Engenharia da Computação - UFES

- -

Seja livre, use GNU/Linux!
Open Source  - Milhares de mentes abertas não podem estar enganadas!
--

--
GUS-BR - Grupo de Usuários de Slackware Brasil
http://www.slackwarebrasil.org/
http://groups.google.com/group/slack-users-br

Antes de perguntar:
http://www.istf.com.br/perguntas/

Para sair da lista envie um e-mail para:
[email protected]


--
Atenciosamente,

José Miranda
Assessor de TI
Semana da Engenharia 2012
www.semanadaeng.com.br
skype: joseph.inf
telefone: (27) 9867-2303
Engenharia da Computação - UFES

- -

Seja livre, use GNU/Linux!
Open Source  - Milhares de mentes abertas não podem estar enganadas!
--

--
GUS-BR - Grupo de Usuários de Slackware Brasil
http://www.slackwarebrasil.org/
http://groups.google.com/group/slack-users-br

Antes de perguntar:
http://www.istf.com.br/perguntas/

Para sair da lista envie um e-mail para:
[email protected]


--
Atenciosamente,

José Miranda
Assessor de TI
Semana da Engenharia 2012
www.semanadaeng.com.br
skype: joseph.inf
telefone: (27) 9867-2303
Engenharia da Computação - UFES

- -

Seja livre, use GNU/Linux!
Open Source  - Milhares de mentes abertas não podem estar enganadas!
--

--
GUS-BR - Grupo de Usuários de Slackware Brasil
http://www.slackwarebrasil.org/
http://groups.google.com/group/slack-users-br

Antes de perguntar:
http://www.istf.com.br/perguntas/

Para sair da lista envie um e-mail para:
[email protected]


--
Atenciosamente,

José Miranda
Assessor de TI
Semana da Engenharia 2012
www.semanadaeng.com.br
skype: joseph.inf
telefone: (27) 9867-2303
Engenharia da Computação - UFES

- -

Seja livre, use GNU/Linux!
Open Source  - Milhares de mentes abertas não podem estar enganadas!
--

--
GUS-BR - Grupo de Usuários de Slackware Brasil
http://www.slackwarebrasil.org/
http://groups.google.com/group/slack-users-br

Antes de perguntar:
http://www.istf.com.br/perguntas/

Para sair da lista envie um e-mail para:
[email protected]



--
Atenciosamente,

José Miranda
Assessor de TI
Semana da Engenharia 2012
www.semanadaeng.com.br
skype: joseph.inf
telefone: (27) 9867-2303
Engenharia da Computação - UFES

- -

Seja livre, use GNU/Linux!
Open Source  - Milhares de mentes abertas não podem estar enganadas!
--

--
GUS-BR - Grupo de Usuários de Slackware Brasil
http://www.slackwarebrasil.org/
http://groups.google.com/group/slack-users-br

Antes de perguntar:
http://www.istf.com.br/perguntas/

Para sair da lista envie um e-mail para:
[email protected]

Responder a