foi mal Ellington. segue o wpa_supplicant corrigido conforme orientado.
valeu
network={
scan_ssid=0
ssid="rede"
proto=WPA RSN
key_management=WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP WEP104 WEP40
#psk="minhasenha"
psk=d95d8f1f9db89340855fd79dab55f785be9da1a5743dbb55d2c73729b10ec886
priority=10
}
~
~
~
~
~
~
~
~
~
wrote /etc/wpa_supplicant.conf, 11 lines, 283 chars
Em 27 de novembro de 2011 09:15, Ellington Santos <[email protected]
> escreveu:
> Cezar,
>
> A configuração key no iwconfig aplica-se apenas para chaves WEP.
>
> Posta o seu wpa_supplicant pra gente ver o q há de errado.
>
>
>
> On Sun, Nov 27, 2011 at 12:10 AM, Cezar Rangel <[email protected]>
> wrote:
> > Olá a todos. Bem com tudo o que foi exposto, parti para a prática. Tudo
> > aparentemente dá certo. A configuração do wpa_supplicant.conf foi bem. A
> > placa é reconhecida a rede idem. Só que acabo por não conseguir conexão.
> > Ao aplicar o comando abaixo, não finaliza nunca:
> > #wpa_supplicant -i wlan0 -c /etc/wpa_supplicant.conf -d -D wext
> >
> ....................................................................................................
> > Starting AP scan for wildcard SSID
> > ioctl[SIOCSIWSCAN]: Network is down
> > Scan requested (ret=-1) - scan timeout 30 seconds
> > Failed to initiate AP scan.
> > State: SCANNING -> DISCONNECTED
> > wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
> > netlink: Operstate: linkmode=-1, operstate=5
> > Setting scan request: 1 sec 0 usec
> > State: DISCONNECTED -> SCANNING
> > Starting AP scan for wildcard SSID
> > ioctl[SIOCSIWSCAN]: Network is down
> > Scan requested (ret=-1) - scan timeout 30 seconds
> > Failed to initiate AP scan.
> > State: SCANNING -> DISCONNECTED
> > wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
> > netlink: Operstate: linkmode=-1, operstate=5
> > Setting scan request: 1 sec 0 usec
> > State: DISCONNECTED -> SCANNING
> > Starting AP scan for wildcard SSID
> > ioctl[SIOCSIWSCAN]: Network is down
> > Scan requested (ret=-1) - scan timeout 30 seconds
> > Failed to initiate AP scan.
> > State: SCANNING -> DISCONNECTED
> > wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
> > netlink: Operstate: linkmode=-1, operstate=5
> > Setting scan request: 1 sec 0 usec
> > State: DISCONNECTED -> SCANNING
> > Starting AP scan for wildcard SSID
> > ioctl[SIOCSIWSCAN]: Network is down
> > Scan requested (ret=-1) - scan timeout 30 seconds
> > Failed to initiate AP scan.
> > State: SCANNING -> DISCONNECTED
> > wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
> > netlink: Operstate: linkmode=-1, operstate=5
> > Setting scan request: 1 sec 0 usec
> > ^CCTRL-EVENT-TERMINATING - signal 2 received
> > Removing interface wlan0
> > No keys have been configured - skip key clearing
> > State: DISCONNECTED -> DISCONNECTED
> > wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
> > netlink: Operstate: linkmode=-1, operstate=5
> > EAPOL: External notification - portEnabled=0
> > EAPOL: Supplicant port status: Unauthorized
> > EAPOL: External notification - portValid=0
> > EAPOL: Supplicant port status: Unauthorized
> > EAPOL: External notification - EAP success=0
> > EAPOL: Supplicant port status: Unauthorized
> > wpa_driver_wext_set_countermeasures
> > No keys have been configured - skip key clearing
> > Removed BSSID 00:21:29:d7:99:51 from blacklist (clear)
> > Removed BSSID 00:00:00:00:00:00 from blacklist (clear)
> > Cancelling scan request
> > Cancelling authentication timeout
> > netlink: Operstate: linkmode=0, operstate=6
> > WPA: Key negotiation completed with 00:21:29:d7:99:51 [PTK=CCMP GTK=TKIP]
> > Cancelling authentication timeout
> > State: GROUP_HANDSHAKE -> COMPLETED
> > CTRL-EVENT-CONNECTED - Connection to 00:21:29:d7:99:51 completed (auth)
> > [id=0 id_str=]
> > wpa_driver_wext_set_operstate: operstate 0->1 (UP)
> > netlink: Operstate: linkmode=-1, operstate=6
> > EAPOL: External notification - portValid=1
> > EAPOL: External notification - EAP success=1
> > EAPOL: SUPP_PAE entering state AUTHENTICATING
> > EAPOL: SUPP_BE entering state SUCCESS
> > EAP: EAP entering state DISABLED
> > EAPOL: SUPP_PAE entering state AUTHENTICATED
> > EAPOL: Supplicant port status: Authorized
> > EAPOL: SUPP_BE entering state IDLE
> > EAPOL authentication completed successfully
> > RTM_NEWLINK: operstate=1 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
> > RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added
> > EAPOL: startWhen --> 0
> > EAPOL: disable timer tick
> >
> ..............................................................................................
> >
> > # iwconfig wlan0 key 78901iuytoplj88a
> > Error for wireless request "Set Encode" (8B2A) :
> > invalid argument "78901iuytoplj88a".
> > bash-4.1#
> >
> ..............................................................................................
> > Já o comando abaixo dá retorno:
> > bash-4.1# wpa_passphrase razec 78901iuytoplj88a
> > network={
> > ssid="razec"
> > #psk="78901iuytoplj88a"
> >
> psk=d407b1adaabdd99d354cc8c0a1de863b9bf6fc72fa11655e1f7a32c954272192
> > }
> >
> > Enfim, não estou conseguindo conectar
> >
> > Em 26 de novembro de 2011 10:59, Marcelo ND <[email protected]>
> > escreveu:
> >>
> >>
> >> Em 25 de novembro de 2011 00:11, Sergio Mira <[email protected]>
> escreveu:
> >>>
> >>> Minha primeira pergunta seria: por que não utilizar o wicd?
> >>
> >> Um porquê não usar wicd não existe. Mas.
> >> Quem quer aprender e ver como "as coisas" funcionam "vai na mão".
> >>
> >> --
> >> GUS-BR - Grupo de Usuários de Slackware Brasil
> >> http://www.slackwarebrasil.org/
> >> http://groups.google.com/group/slack-users-br
> >>
> >> Antes de perguntar:
> >> http://www.istf.com.br/perguntas/
> >>
> >> Para sair da lista envie um e-mail para:
> >> [email protected]
> >
> >
> > --
> > Cezar Rangel
> > [email protected]
> >
> > --
> > GUS-BR - Grupo de Usuários de Slackware Brasil
> > http://www.slackwarebrasil.org/
> > http://groups.google.com/group/slack-users-br
> >
> > Antes de perguntar:
> > http://www.istf.com.br/perguntas/
> >
> > Para sair da lista envie um e-mail para:
> > [email protected]
>
> --
> GUS-BR - Grupo de Usuários de Slackware Brasil
> http://www.slackwarebrasil.org/
> http://groups.google.com/group/slack-users-br
>
> Antes de perguntar:
> http://www.istf.com.br/perguntas/
>
> Para sair da lista envie um e-mail para:
> [email protected]
>
--
* Cezar Rangel*
*[email protected]*
--
GUS-BR - Grupo de Usuários de Slackware Brasil
http://www.slackwarebrasil.org/
http://groups.google.com/group/slack-users-br
Antes de perguntar:
http://www.istf.com.br/perguntas/
Para sair da lista envie um e-mail para:
[email protected]
