Depois do wpa_supplicant -i wlan0.... execute um iwconfig wlan0 e veja se o campo Access Point contém o MAC do seu AP.
On Sun, Nov 27, 2011 at 9:52 AM, Cezar Rangel <[email protected]> wrote: > foi mal Ellington. segue o wpa_supplicant corrigido conforme orientado. > valeu > > network={ > scan_ssid=0 > ssid="rede" > proto=WPA RSN > key_management=WPA-PSK > pairwise=CCMP TKIP > group=CCMP TKIP WEP104 WEP40 > #psk="minhasenha" > psk=d95d8f1f9db89340855fd79dab55f785be9da1a5743dbb55d2c73729b10ec886 > priority=10 > } > ~ > ~ > ~ > ~ > ~ > ~ > ~ > ~ > ~ > wrote /etc/wpa_supplicant.conf, 11 lines, 283 chars > > Em 27 de novembro de 2011 09:15, Ellington Santos > <[email protected]> escreveu: >> >> Cezar, >> >> A configuração key no iwconfig aplica-se apenas para chaves WEP. >> >> Posta o seu wpa_supplicant pra gente ver o q há de errado. >> >> >> >> On Sun, Nov 27, 2011 at 12:10 AM, Cezar Rangel <[email protected]> >> wrote: >> > Olá a todos. Bem com tudo o que foi exposto, parti para a prática. Tudo >> > aparentemente dá certo. A configuração do wpa_supplicant.conf foi bem. A >> > placa é reconhecida a rede idem. Só que acabo por não conseguir conexão. >> > Ao aplicar o comando abaixo, não finaliza nunca: >> > #wpa_supplicant -i wlan0 -c /etc/wpa_supplicant.conf -d -D wext >> > >> > .................................................................................................... >> > Starting AP scan for wildcard SSID >> > ioctl[SIOCSIWSCAN]: Network is down >> > Scan requested (ret=-1) - scan timeout 30 seconds >> > Failed to initiate AP scan. >> > State: SCANNING -> DISCONNECTED >> > wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT) >> > netlink: Operstate: linkmode=-1, operstate=5 >> > Setting scan request: 1 sec 0 usec >> > State: DISCONNECTED -> SCANNING >> > Starting AP scan for wildcard SSID >> > ioctl[SIOCSIWSCAN]: Network is down >> > Scan requested (ret=-1) - scan timeout 30 seconds >> > Failed to initiate AP scan. >> > State: SCANNING -> DISCONNECTED >> > wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT) >> > netlink: Operstate: linkmode=-1, operstate=5 >> > Setting scan request: 1 sec 0 usec >> > State: DISCONNECTED -> SCANNING >> > Starting AP scan for wildcard SSID >> > ioctl[SIOCSIWSCAN]: Network is down >> > Scan requested (ret=-1) - scan timeout 30 seconds >> > Failed to initiate AP scan. >> > State: SCANNING -> DISCONNECTED >> > wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT) >> > netlink: Operstate: linkmode=-1, operstate=5 >> > Setting scan request: 1 sec 0 usec >> > State: DISCONNECTED -> SCANNING >> > Starting AP scan for wildcard SSID >> > ioctl[SIOCSIWSCAN]: Network is down >> > Scan requested (ret=-1) - scan timeout 30 seconds >> > Failed to initiate AP scan. >> > State: SCANNING -> DISCONNECTED >> > wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT) >> > netlink: Operstate: linkmode=-1, operstate=5 >> > Setting scan request: 1 sec 0 usec >> > ^CCTRL-EVENT-TERMINATING - signal 2 received >> > Removing interface wlan0 >> > No keys have been configured - skip key clearing >> > State: DISCONNECTED -> DISCONNECTED >> > wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT) >> > netlink: Operstate: linkmode=-1, operstate=5 >> > EAPOL: External notification - portEnabled=0 >> > EAPOL: Supplicant port status: Unauthorized >> > EAPOL: External notification - portValid=0 >> > EAPOL: Supplicant port status: Unauthorized >> > EAPOL: External notification - EAP success=0 >> > EAPOL: Supplicant port status: Unauthorized >> > wpa_driver_wext_set_countermeasures >> > No keys have been configured - skip key clearing >> > Removed BSSID 00:21:29:d7:99:51 from blacklist (clear) >> > Removed BSSID 00:00:00:00:00:00 from blacklist (clear) >> > Cancelling scan request >> > Cancelling authentication timeout >> > netlink: Operstate: linkmode=0, operstate=6 >> > WPA: Key negotiation completed with 00:21:29:d7:99:51 [PTK=CCMP >> > GTK=TKIP] >> > Cancelling authentication timeout >> > State: GROUP_HANDSHAKE -> COMPLETED >> > CTRL-EVENT-CONNECTED - Connection to 00:21:29:d7:99:51 completed (auth) >> > [id=0 id_str=] >> > wpa_driver_wext_set_operstate: operstate 0->1 (UP) >> > netlink: Operstate: linkmode=-1, operstate=6 >> > EAPOL: External notification - portValid=1 >> > EAPOL: External notification - EAP success=1 >> > EAPOL: SUPP_PAE entering state AUTHENTICATING >> > EAPOL: SUPP_BE entering state SUCCESS >> > EAP: EAP entering state DISABLED >> > EAPOL: SUPP_PAE entering state AUTHENTICATED >> > EAPOL: Supplicant port status: Authorized >> > EAPOL: SUPP_BE entering state IDLE >> > EAPOL authentication completed successfully >> > RTM_NEWLINK: operstate=1 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) >> > RTM_NEWLINK, IFLA_IFNAME: Interface 'wlan0' added >> > EAPOL: startWhen --> 0 >> > EAPOL: disable timer tick >> > >> > .............................................................................................. >> > >> > # iwconfig wlan0 key 78901iuytoplj88a >> > Error for wireless request "Set Encode" (8B2A) : >> > invalid argument "78901iuytoplj88a". >> > bash-4.1# >> > >> > .............................................................................................. >> > Já o comando abaixo dá retorno: >> > bash-4.1# wpa_passphrase razec 78901iuytoplj88a >> > network={ >> > ssid="razec" >> > #psk="78901iuytoplj88a" >> > >> > psk=d407b1adaabdd99d354cc8c0a1de863b9bf6fc72fa11655e1f7a32c954272192 >> > } >> > >> > Enfim, não estou conseguindo conectar >> > >> > Em 26 de novembro de 2011 10:59, Marcelo ND <[email protected]> >> > escreveu: >> >> >> >> >> >> Em 25 de novembro de 2011 00:11, Sergio Mira <[email protected]> >> >> escreveu: >> >>> >> >>> Minha primeira pergunta seria: por que não utilizar o wicd? >> >> >> >> Um porquê não usar wicd não existe. Mas. >> >> Quem quer aprender e ver como "as coisas" funcionam "vai na mão". >> >> >> >> -- >> >> GUS-BR - Grupo de Usuários de Slackware Brasil >> >> http://www.slackwarebrasil.org/ >> >> http://groups.google.com/group/slack-users-br >> >> >> >> Antes de perguntar: >> >> http://www.istf.com.br/perguntas/ >> >> >> >> Para sair da lista envie um e-mail para: >> >> [email protected] >> > >> > >> > -- >> > Cezar Rangel >> > [email protected] >> > >> > -- >> > GUS-BR - Grupo de Usuários de Slackware Brasil >> > http://www.slackwarebrasil.org/ >> > http://groups.google.com/group/slack-users-br >> > >> > Antes de perguntar: >> > http://www.istf.com.br/perguntas/ >> > >> > Para sair da lista envie um e-mail para: >> > [email protected] >> >> -- >> GUS-BR - Grupo de Usuários de Slackware Brasil >> http://www.slackwarebrasil.org/ >> http://groups.google.com/group/slack-users-br >> >> Antes de perguntar: >> http://www.istf.com.br/perguntas/ >> >> Para sair da lista envie um e-mail para: >> [email protected] > > > -- > Cezar Rangel > [email protected] > > -- > GUS-BR - Grupo de Usuários de Slackware Brasil > http://www.slackwarebrasil.org/ > http://groups.google.com/group/slack-users-br > > Antes de perguntar: > http://www.istf.com.br/perguntas/ > > Para sair da lista envie um e-mail para: > [email protected] -- GUS-BR - Grupo de Usuários de Slackware Brasil http://www.slackwarebrasil.org/ http://groups.google.com/group/slack-users-br Antes de perguntar: http://www.istf.com.br/perguntas/ Para sair da lista envie um e-mail para: [email protected]
