|
I install them without anything thinking they were
waterproof maybe I need to go back and check them all now after reading up on
this. I usually try and cable tie them so the ends are NOT facing up and down
and so far that has worked. We have not had a lot of rain here in CA so that
might be a good thing and why I have not seen any problems but when I do is
there any particular symptoms to look for other then strange radio behavior?
could SB possible include a small roll of Monkey Snot with each radio? I know
when I order a 5 pack of ants from my vendor in the box are 5 small rolls of
that mastic tap that works AWESOME! to seal up the N
connector..
I mean come on how many monkeys does it take to
blow their nose to collect enough snot to give to us for free
heheheheh
----- Original Message -----
Sent: Thursday, July 24, 2003 8:21
AM
Subject: Re: [smartBridges] Are Ethernet
connections sensitive to rust & oxide????
How are most people installing them??
----- Original Message -----
Sent: Thursday, July 24, 2003 11:10
AM
Subject: Re: [smartBridges] Are
Ethernet connections sensitive to rust & oxide????
The point is that the connector is not very waterproof the
way most people install them. In that case, yes, it will
corrode.
Kevin
Pascal Losier wrote:
I use the black Mastic which seal it.... The tape is only to protect the
mastic from the sun.
You need tape & mastic.......mastic alone will shrink, Tape alone will
leak..
What I mean is... If the connector is watherproof....... Will it rust ?
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]] On Behalf Of Shawn Mitchell
Sent: Thursday, July 24, 2003 4:55 AM
To: [EMAIL PROTECTED]
Subject: RE: [smartBridges] Are Ethernet connections sensitive to rust &
oxide????
I don't trust using black tape, it's not waterproof. You can think it
us, but it's not. If your going to have a RJ-45 connection outside, use
a weather proofing kit. It's basically a highly malleable tar like
substance that you mold around the entire connector. Makes it totally
waterproof in all kinds of weather.
It either that, or for the couplers I use silicone around the entire
thing. Not a light coating of it, but a nice large amount. I've cut off
the silicone after a nice hard rain, and they've always been dry as a
bone. When I first started doing I wrapped them a large amount of black
tape, and I always had a problem with corrosion after a few months. Now
I don't have any problems.
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]]On Behalf Of Roger Hartley
Sent: Wednesday, July 23, 2003 22:04
To: [EMAIL PROTECTED]
Subject: Re: [smartBridges] Are ethernet connection sensible to rust &
oxide????
I'm not an expert and can't quote scientific studies, but I can say YES,
cat5 connections are totally screwed up by oxidation and corrosion.
You'll get weird behavior that is very hard to figure out logically.
Remove the corroded parts and everything starts to work as planned. The
main thing to avoid is the moisture that causes the rust and corrosion.
Pascal Losier wrote:
I used waterproofing mastic and tape on the regular sheilded RJ-45C
connector.
Once you waterproof your installs with black mastic & Tape,
No water will ever get in.
I dont trust those little fitting on APP.... So I remove it.
But How about rust,...
Are ethernet connection sensible to rust & oxide ????
Im in satellite buisness since last 10 years so my connector use to be
coaxials. They are a lot bigger.
So rust & cold connection were not an issue.
Are ethernet connection sensible to rust & oxide ????
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]] On Behalf Of Roger Hartley
Sent: Wednesday, July 23, 2003 10:26 PM
To: [EMAIL PROTECTED]
Subject: Re: [smartBridges] Cat5 for outdoor installs
A few days ago, I had one of my most important customers go completely
off the air. I did a lot of trouble shooting and found out it was the
airBridge Total "waterproof" connector had allowed water in. Maybe I
don't know the correct way to install it, I thought I did. But after
drying out the connectors, recrimping the end towards the house, it
still wouldn't work. I cut off about a foot of the cable going into
the house and pulled out some of the individual wires, they were wet
inside the jacket. This customer now has gel-filled cable going from
the connector to the router ... *and* I used waterproofing mastic and
tape on the waterproof connector.
Laurence Laforga wrote:
Is that one gel-filled? I recall someone saying that the gel-filled is
ideal for underground type of install and that just the UV rated ones
are required and cheaper for outdoor installs on roofs and such.
I use the Tyco brand for CSC and don't have a problem with crimping.
-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]]On Behalf Of Patrick
Sent: Wednesday, July 23, 2003 8:49 AM
To: [EMAIL PROTECTED]
Subject: Re: [smartBridges] Cat5 for outdoor installs
I concur that it is a PITA to crimp! Anyone know if there are
connectors
that fit it better to make crimping easier?
----- Original Message -----
From: "Roger Hartley" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Wednesday, July 23, 2003 10:11 AM
Subject: Re: [smartBridges] Cat5 for outdoor installs
prefix: cwc
part # 5exho4p24bkrmohpv
This is the gel-filled type. Seems to be very good quality, but
a PITA
to crimp.
David Ross Buckley wrote:
I recall some posts awhile back about recommended cat5 cable
for outdoor
installs. I believe someone even gave a part number from
Graybar. If
possible can we get that number again, it would be greatly
appreciated.
Thanks in advance.
The PART-15.ORG smartBridges Discussion List
To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe
smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in
the body type unsubscribe
smartBridges)
Archives: http://archives.part-15.org
The PART-15.ORG smartBridges Discussion List
To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe
smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in
the body type unsubscribe smartBridges)
Archives: http://archives.part-15.org
The PART-15.ORG smartBridges Discussion List
To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname>
To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges)
Archives: http://archives.part-15.org
--
Kevin B. Proctor
Customer Service
Internet Sales
Electro-Comm Distributing Inc.
5015 Paris St.
Denver, CO 80239
+1-800-525-0173
+1-303-371-8182
+1-303-371-8158 FAX
+1-800-423-8018 FAX
[EMAIL PROTECTED]
The PART-15.ORG smartBridges Discussion List To Join:
mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges
To Remove: mailto:[EMAIL PROTECTED] (in the body type
unsubscribe smartBridges) Archives: http://archives.part-15.org
|
