It has two antenna jacks on the indoor unit. JH ----- Original Message ----- From: <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Saturday, August 02, 2003 7:34 AM Subject: Re: [smartBridges] Connecting with low signal
> You used a splitter, or are there two ports on the Indoor AirPoint Pro? > Does it use one at a time and switch back and forth like Cisco does? > > On Sat, 2 Aug 2003, John Banes wrote: > > > You might consider an AirPoint Pro and 2 antennas and run diversity. I tried > > that at one location with a LOT of multipath and it helped more than an amp. > > Or possibly you could stick a repeater someplace temporarily until you get > > your new towers in place. > > > > John > > > > ----- Original Message ----- > > From: "Jeremy Oswalt" <[EMAIL PROTECTED]> > > To: <[EMAIL PROTECTED]> > > Sent: Saturday, August 02, 2003 06:16 AM > > Subject: Re: [smartBridges] Connecting with low signal > > > > > > > I was afraid of that. Though I have several customers with low signal, > > but I think this one is the lowest. The have a 24 db grid already. I have > > a feeling we are cutting through a tree or two. > > > > > > I may have them wait until I get my other two towers up. This customer is > > pretty understanding. Worse case, I'll get an amp, but I'm trying to avoid > > that. > > > > > > > Your signal is probably too weak My experience has been that it needs > > 60-70% > > > > to work at all and it is happiest above 80% > > > > > > > > John > > > > ----- Original Message ----- > > > > From: "Jeremy Oswalt" <[EMAIL PROTECTED]> > > > > To: <[EMAIL PROTECTED]> > > > > Sent: Friday, August 01, 2003 07:37 PM > > > > Subject: [smartBridges] Connecting with low signal > > > > > > > > > > > > > We installed a customer today using an ABO. The RSSI was between 29% > > and > > > > 40% with the signal strength floating between 50% and 67%. After > > spending > > > > hours putting up the guyed mast and running the wire, we tested the > > > > connection and can't get it to ping anything. We checked the MAC > > > > authentication table and it is entered. We reentered the WEP key and > > the > > > > administrator password. It associates, but we can't ping or get to > > anything > > > > on my network or the Internet. I'm using the latest firmware 1.07. > > > > > > > > > > I checked on the Access point and it sees it associated, but the > > signal > > > > properties are 0 and it shows it trasmitting data. If you look at the > > > > statistics on the ABO when you ping, it shows the failed packets, but > > the > > > > receive and transmit statistics are showing no errors. What am I > > missing? > > > > This is about our 20th customer using Airbridges, so we've done this > > before. > > > > Any ideas? > > > > > The PART-15.ORG smartBridges Discussion List > > > > > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > > > > smartBridges <yournickname> > > > > > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > > > > smartBridges) > > > > > Archives: http://archives.part-15.org > > > > > > > > > > > > > > > > > The PART-15.ORG smartBridges Discussion List > > > > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > > smartBridges <yournickname> > > > > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > > smartBridges) > > > > Archives: http://archives.part-15.org > > > > > > The PART-15.ORG smartBridges Discussion List > > > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > > smartBridges <yournickname> > > > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > > smartBridges) > > > Archives: http://archives.part-15.org > > > > > > > > > The PART-15.ORG smartBridges Discussion List > > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> > > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) > > Archives: http://archives.part-15.org > > > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) > Archives: http://archives.part-15.org The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org
