That's what I'm talking about. You (we) shouldn't need to do that. While the 12 vdc may be enough for most applications, SB should make the 18/24 vdc powershots available, since they even mention in the manual that comes with the units to use them on longer cable runs.
I had a need for one and had a heck of a time finding one. I had a friend who sent me an 18 vdc power supply and helped me convert it to work with the powershot, but that shouldn't be required. (Not a jab at SB...just a friendly suggestion. :) Sam On Wed, 6 Aug 2003, Roger Howard wrote: > Ooh.. I thought you meant the actual plug... the barrel connector that fits > into the airbridge. I normally cut it off the 12 volt one that's supplied > and solder it onto an 18v supply when needed. > > ----- Original Message ----- > From: "Sam" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Wednesday, August 06, 2003 9:23 AM > Subject: Re: [smartBridges] AirPoint-Pro Outdoor > > > > I have never received an 18 volt powershot with any of the units I have > > purchased. They are all 12 volt. > > > > On Wed, 6 Aug 2003, Roger Howard wrote: > > > > > They do.. you get one with every unit :) > > > > > > ----- Original Message ----- > > > From: "Sam" <[EMAIL PROTECTED]> > > > To: <[EMAIL PROTECTED]> > > > Sent: Wednesday, August 06, 2003 9:12 AM > > > Subject: RE: [smartBridges] AirPoint-Pro Outdoor > > > > > > > > > > Seeni > > > > > > > > Why doesn't Smartbridges make these plugs available? > > > > > > > > Sam > > > > > > > > On Wed, 6 Aug 2003, sBTech wrote: > > > > > > > > > Hi Rob Cleminson, > > > > > > > > > > > > > > > > > > > > An 18 V DC plug is an ideal and sufficient plug however you have to > make > > > > > sure that the polarity of the plug should as specified in the > website. > > > > > > > > > > http://www.smartbridges.com/new/products/ps.php > > > > > > > > > > > > > > > > > > > > Few customers are using Motorola Canopy Powershot which is 24V and > it is > > > > > same pin as sB. > > > > > > > > > > Also you can use the following powersupply, however you need to > change > > > > > the Pin polarity as stated in the specification. > > > > > > > > > > Brand: Mouser > > > > > > > > > > Model: 552-PSA-31U-180 [EMAIL PROTECTED] > > > > > > > > > > > > > > > > > > > > To help you procure the correct power supply adapter, the > specification > > > > > of the power adapter is :- > > > > > > > > > > > > > > > Output Voltage Range > > > > > > > > > > Regulated between 15V to 18V (max) > > > > > > > > > > > > > > > Current Ratings > > > > > > > > > > 1 Ampere > > > > > > > > > > > > > > > Type of Plug > > > > > > > > > > Barrel Type > > > > > > > > > > > > > > > Plug Polarity > > > > > > > > > > outer body = +ve, center = -ve > > > > > > > > > > > > > > > > > > > > Diameter of plug > > > > > > > > > > Inner Diameter of the plug = 2.5mm > > > > > Outer Diameter of the plug = 5.5mm > > > > > > > > > > > > > > > Length of the plug > > > > > > > > > > 10mm or more > > > > > > > > > > > > > > > > > > > > Thank you > > > > > > > > > > > > > > > > > > > > Seeni, SB support > > > > > > > > > > > > > > > > > > > > -----Original Message----- > > > > > From: [EMAIL PROTECTED] > > > > > [mailto:[EMAIL PROTECTED] On Behalf Of Rob Cleminson > > > > > Sent: Wednesday, August 06, 2003 12:57 AM > > > > > To: '[EMAIL PROTECTED]' > > > > > Subject: [smartBridges] AirPoint-Pro Outdoor > > > > > > > > > > > > > > > > > > > > Hi, > > > > > > > > > > > > > > > > > > > > I just purchased my first Airpoint Pro Outdoor - Powered it up fine > on > > > > > my desk. > > > > > > > > > > > > > > > > > > > > Just got down from installing on my tower - I have 100Metres of CAT5 > and > > > > > now no power is arriving at the unit? > > > > > > > > > > > > > > > > > > > > Is this because I am using the standard 12V AC Adapter and because > of > > > > > the extra cable length now need 15V. There is a note in the booklet > > > > > suggesting that this is best but I am not sure if it is a MUST > > > > > > > > > > > > > > > > > > > > Any advice? > > > > > > > > > > > > > > > > > > > > Regards > > > > > > > > > > > > > > > > > > > > Rob Cleminson > > > > > > > > > > > > > > > > > > > > > > > > > > > > The PART-15.ORG smartBridges Discussion List > > > > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > > > smartBridges <yournickname> > > > > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > > > smartBridges) > > > > Archives: http://archives.part-15.org > > > > > > The PART-15.ORG smartBridges Discussion List > > > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges <yournickname> > > > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > smartBridges) > > > Archives: http://archives.part-15.org > > > > > > > The PART-15.ORG smartBridges Discussion List > > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges <yournickname> > > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > smartBridges) > > Archives: http://archives.part-15.org > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges > <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) > Archives: http://archives.part-15.org > The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org
