Re: [smartBridges] Microcell setup

[Carl A Jeptha]

Here is how the network is laid out now.   Sorry Pascal and the rest for the repeat.   Carl ------ Internet | | -------Cisco Router (Public IP #) | |  Fibre |         207.*.*.* -------Gateway/Firewall (Linux Mandrake MNF) |          10.*.*.? |  Fibre |           10.*.*.! --------Smartbridge (AP Mode) Gateway Address 10.*.*.? | |   Wireless |           10.*.*.~ ----------Smartbridge (Client Bridge Mode) Gateway Address 10.*.*.! | |   Wireless |           10.*.*.@ ----------Dlink 900AP+ (Wireless Client Mode) Gateway Address 10.*.*.? | |   CAT5 |           10.*.*.# ----------Client Computer NIC Gateway Address 10.*.*.?   With this arrangement The client can reach the internet, but the dlink can no longer be managed. ----- Original Message ----- From: Carl A Jeptha To: [EMAIL PROTECTED] Sent: Friday, October 31, 2003 2:53 PM Subject: Re: [smartBridges] Microcell setup Okay got it working will report the setup later. Hint - the gateway is the gateway.   Carl ----- Original Message ----- From: Carl A Jeptha To: [EMAIL PROTECTED] Sent: Friday, October 31, 2003 11:58 AM Subject: Re: [smartBridges] Microcell setup Okay ran the tests and got the same results ;-(   I am now doing to put the DLink 704P between the firewall and the SB Network.   Carl ----- Original Message ----- From: Carl A Jeptha To: [EMAIL PROTECTED] Sent: Friday, October 31, 2003 10:13 AM Subject: Re: [smartBridges] Microcell setup Gentlefolks, it is Halloween Morning I will run this test and let you know the results. I did connect a DLink 704P (Was laying around here) and the setup worked. A little thinking might fix this situation as I would not like to open my system to the internet this way.   Carl ----- Original Message ----- From: Tom Haynes To: [EMAIL PROTECTED] Sent: Friday, October 31, 2003 3:29 AM Subject: RE: [smartBridges] Microcell setup That would indicate that the firewall is upset some how by the MAC NAT. I�m not sure why this would be, though.   From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Wayland Sothcott Sent: Friday, October 31, 2003 3:16 AM To: [EMAIL PROTECTED] Subject: Re: [smartBridges] Microcell setup   That setup should work. However I had a similar problem with reaching the Internet on IP-Cop with the arangement below.   1. Internet 2. IP-Cop Firewal/Gateway 3. Ethernet 4. airBridge 5. Airpoint Pro Outdoor - set in AP Mode 6. airBridge 7. Client Network   It would ping IP-Cop local and Internet interfaces but not the Internet. The solution was to replace 4. airBridge with airPoint in Client Bridge mode;   1. Internet 2. IP-Cop Firewal/Gateway 3. Ethernet 4. Airpoint Pro Outdoor - set in Client Bridge mode 5. Airpoint Pro Outdoor - set in AP Mode 6. airBridge 7. Client Network     Regards, Wayland.   ----- Original Message ----- From: Seeni Mohamed To: [EMAIL PROTECTED] Sent: Friday, October 31, 2003 3:08 AM Subject: RE: [smartBridges] Microcell setup   Hi Carl,   If you are able to ping to the Mandrake Firewall/Gateway means, it shouldn�t be any problem in the wireless link. Please verify the DNS & GW entries in your PC and PING using the GW and DNS IP address from the client PC. If still unable to pass the traffic to the internet or outside the firewall, then please check the firewall policy settings.   Thank you   Kind regards, Seeni -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Carl A Jeptha Sent: Friday, October 31, 2003 7:01 AM To: [EMAIL PROTECTED] Subject: Re: [smartBridges] Microcell setup   I can ping and surf within my private network (10.0.0.0). I cannot ping and surf outside in the public area. I already have a Wavebolt system running for local work on the same network.   Carl ----- Original Message ----- From: Vasu (sB Tech Team) To: [EMAIL PROTECTED] Sent: Thursday, October 30, 2003 5:30 PM Subject: RE: [smartBridges] Microcell setup   Hi Carl,   From the DWL 900AP + when you operate in a wireless client mode and you try to associate to the repeater, are you able to ping the aPPO in repeater mode and get a response?     Vasu -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Carl A Jeptha Sent: Friday, October 31, 2003 6:05 AM To: [EMAIL PROTECTED] Subject: [smartBridges] Microcell setup   I have two Airpoint Pro and one Dlink 900ap+ I would like to start a microcell with them. Below is what I think must be done.   1. Internet 2. Mandrake Firewal/Gateway 3. Fiber to watertower 4. Airpoint Pro Outdoor - set in AP Mode 5. Airpoint Pro Outdoor - set in Repeater Mode 6. DWL 900AP+ - set in Wireless Client Mode 7. Client Network   Right now in this test setup I cannot reach the Internet. Although nthe same Gateway is handling other traffic.   Carl

<<image001.jpg>>