Hello,
Information about above disk drive follows (please see attached file).
--
Tulio Lazarini
https://www.facebook.com/tuliolazarini<http://tulio.lazarini.blog.uol.com.br/>
"Quis custodiet ipsos custodes?
smartctl 5.41 2011-06-09 r3365 [i686-linux-3.2.0-34-generic-pae] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: Hitachi HDS724040ALE640
Serial Number: PK2310PAG0YETM
LU WWN Device Id: 5 000cca 22bc06e88
Firmware Version: MJAOA250
User Capacity: 4.000.787.030.016 bytes [4,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Fri Nov 30 21:15:41 2012 BRST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (34304) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate PO-R-- 100 100 016 - 0
2 Throughput_Performance P-S--- 136 136 054 - 81
3 Spin_Up_Time POS--- 157 157 024 - 508 (Average 474)
4 Start_Stop_Count -O--C- 100 100 000 - 47
5 Reallocated_Sector_Ct PO--CK 100 100 005 - 0
7 Seek_Error_Rate PO-R-- 100 100 067 - 0
8 Seek_Time_Performance P-S--- 121 121 020 - 34
9 Power_On_Hours -O--C- 100 100 000 - 2362
10 Spin_Retry_Count PO--C- 100 100 060 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 44
192 Power-Off_Retract_Count -O--CK 100 100 000 - 106
193 Load_Cycle_Count -O--C- 100 100 000 - 106
194 Temperature_Celsius -O---- 146 146 000 - 41 (Min/Max 22/80)
196 Reallocated_Event_Count -O--CK 100 100 000 - 0
197 Current_Pending_Sector -O---K 100 100 000 - 0
198 Offline_Uncorrectable ---R-- 100 100 000 - 0
199 UDMA_CRC_Error_Count -O-R-- 200 200 000 - 1
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
GP/S Log at address 0x00 has 1 sectors [Log Directory]
SMART Log at address 0x01 has 1 sectors [Summary SMART error log]
GP Log at address 0x03 has 1 sectors [Ext. Comprehensive SMART error log]
GP Log at address 0x04 has 7 sectors [Device Statistics]
SMART Log at address 0x06 has 1 sectors [SMART self-test log]
GP Log at address 0x07 has 1 sectors [Extended self-test log]
GP Log at address 0x08 has 2 sectors [Power Conditions]
SMART Log at address 0x09 has 1 sectors [Selective self-test log]
GP Log at address 0x10 has 1 sectors [NCQ Command Error]
GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters]
GP Log at address 0x20 has 1 sectors [Streaming performance log]
GP Log at address 0x21 has 1 sectors [Write stream error log]
GP Log at address 0x22 has 1 sectors [Read stream error log]
GP/S Log at address 0x80 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x81 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x82 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x83 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x84 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x85 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x86 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x87 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x88 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x89 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8f has 16 sectors [Host vendor specific log]
GP/S Log at address 0x90 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x91 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x92 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x93 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x94 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x95 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x96 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x97 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x98 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x99 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9f has 16 sectors [Host vendor specific log]
GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status]
GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer]
SMART Extended Comprehensive Error Log Version: 1 (1 sectors)
Device Error Count: 1
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 1 [0] occurred at disk power-on lifetime: 6 hours (0 days + 6 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 01 00 00 68 59 42 87 08 00 Error: ICRC, ABRT 1 sectors at LBA =
0x68594287 = 1750680199
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
35 00 00 00 f0 00 00 68 59 41 98 40 00 05:47:50.514 WRITE DMA EXT
35 00 00 00 f0 00 00 68 59 40 a8 40 00 05:47:50.502 WRITE DMA EXT
35 00 00 00 f0 00 00 68 59 3f b8 40 00 05:47:50.497 WRITE DMA EXT
35 00 00 00 f0 00 00 68 59 3e c8 40 00 05:47:50.493 WRITE DMA EXT
35 00 00 00 f0 00 00 68 59 3d d8 40 00 05:47:50.483 WRITE DMA EXT
SMART Extended Self-test Log Version: 1 (1 sectors)
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 256 (0x0100)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 40 Celsius
Power Cycle Min/Max Temperature: 32/44 Celsius
Lifetime Min/Max Temperature: 22/80 Celsius
Under/Over Temperature Limit Count: 0/0
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -40/70 Celsius
Temperature History Size (Index): 128 (62)
Index Estimated Time Temperature Celsius
63 2012-11-30 19:08 40 *********************
64 2012-11-30 19:09 40 *********************
65 2012-11-30 19:10 40 *********************
66 2012-11-30 19:11 41 **********************
67 2012-11-30 19:12 40 *********************
... ..( 5 skipped). .. *********************
73 2012-11-30 19:18 40 *********************
74 2012-11-30 19:19 41 **********************
75 2012-11-30 19:20 41 **********************
76 2012-11-30 19:21 40 *********************
... ..( 3 skipped). .. *********************
80 2012-11-30 19:25 40 *********************
81 2012-11-30 19:26 41 **********************
82 2012-11-30 19:27 41 **********************
83 2012-11-30 19:28 40 *********************
84 2012-11-30 19:29 41 **********************
85 2012-11-30 19:30 40 *********************
86 2012-11-30 19:31 41 **********************
... ..( 18 skipped). .. **********************
105 2012-11-30 19:50 41 **********************
106 2012-11-30 19:51 40 *********************
107 2012-11-30 19:52 41 **********************
108 2012-11-30 19:53 40 *********************
109 2012-11-30 19:54 41 **********************
... ..( 4 skipped). .. **********************
114 2012-11-30 19:59 41 **********************
115 2012-11-30 20:00 40 *********************
116 2012-11-30 20:01 40 *********************
117 2012-11-30 20:02 41 **********************
118 2012-11-30 20:03 41 **********************
119 2012-11-30 20:04 40 *********************
120 2012-11-30 20:05 41 **********************
... ..( 2 skipped). .. **********************
123 2012-11-30 20:08 41 **********************
124 2012-11-30 20:09 40 *********************
125 2012-11-30 20:10 40 *********************
126 2012-11-30 20:11 40 *********************
127 2012-11-30 20:12 41 **********************
... ..( 43 skipped). .. **********************
43 2012-11-30 20:56 41 **********************
44 2012-11-30 20:57 40 *********************
45 2012-11-30 20:58 41 **********************
... ..( 4 skipped). .. **********************
50 2012-11-30 21:03 41 **********************
51 2012-11-30 21:04 40 *********************
52 2012-11-30 21:05 41 **********************
53 2012-11-30 21:06 40 *********************
54 2012-11-30 21:07 41 **********************
... ..( 4 skipped). .. **********************
59 2012-11-30 21:12 41 **********************
60 2012-11-30 21:13 40 *********************
61 2012-11-30 21:14 40 *********************
62 2012-11-30 21:15 41 **********************
SCT Error Recovery Control:
Read: Disabled
Write: Disabled
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0009 2 17 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 14 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
------------------------------------------------------------------------------
Keep yourself connected to Go Parallel:
TUNE You got it built. Now make it sing. Tune shows you how.
http://goparallel.sourceforge.net
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
