Hi
Just received my 5501-70. It comes with BIOS 1.33 and (unlike many
others on this list) has no problems at all seeing and booting off the
8G Sandisk Extreme III CF card I fitted. However it refuses point-blank
to see the WD 320G SATA HD I fitted. It doesn't appear on the device
listing at the beginning and is marked "ignored (disabled)" when OpenBSD
has a go. I mangled the supplied SATA lead when removing it from the
mounting kit so I'm using a random SATA lead that I had lying around. I
can see the drive and it appears to work if I plug the SATA lead into my
PC (leaving it powered by the 5501) so its not the power, lead or the
drive. Is there something you have to set to get the 5501 to look at
the SATA? (I want it to boot from the CF like it does at the moment but
to have the HD for bulk storage.)
Any clues? I enclose a boot log in case it helps.
Thanks
John Cox
Drive is a Western Digital 320GB Scorpio 5400RPM S150 8MB 2.5"
mfr#: WD3200BEVT
Boot log (some control chars removed):
POST: 012345689bcefghips1234ajklnopqr,,,tvwxy
comBIOS ver. 1.33 20070103 Copyright (C) 2000-2007 Soekris
Engineering.
net5501
CPU Geode LX 500 Mhz
0000 Mbyte Memory
0512
Pri Mas SanDisk SDCFX3-8192 LBA Xlt 996-255-63 8003 Mbyte
Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2 Int
-------------------------------------------------------------------
0:01:2 1022 2082 10100000 0006 0220 08 00 00 A0000000 00000000 10
0:06:0 1106 3053 02000096 0117 0210 08 40 00 0000E101 A0004000 11
0:07:0 1106 3053 02000096 0117 0210 08 40 00 0000E201 A0004100 05
0:08:0 1106 3053 02000096 0117 0210 08 40 00 0000E301 A0004200 09
0:09:0 1106 3053 02000096 0117 0210 08 40 00 0000E401 A0004300 12
0:14:0 8086 1074 02000005 0117 8230 08 40 00 A0020000 A0140000 10
0:20:0 1022 2090 06010003 0009 02A0 08 40 80 00006001 00006101
0:20:2 1022 209A 01018001 0005 02A0 08 00 00 00000000 00000000
0:21:0 1022 2094 0C031002 0006 0230 08 00 80 A01E0000 00000000 15
0:21:1 1022 2095 0C032002 0006 0230 08 00 00 A01E1000 00000000 15
Seconds to automatic boot. Press Ctrl-P for entering Monitor.
Using drive 0, partition 3.
Loading...
probing: pc0 com0 com1 pci mem[639K 511M a20=on]
disk: hd0+
>> OpenBSD/i386 BOOT 3.01
com0: 9600 baud
switching console to com0
>> OpenBSD/i386 BOOT 3.01
boot>
booting hd0a:/bsd: 5913424|[52+306864+287943]=0x72a4d4
entry point at 0x200120ªÿ
[ using 595232 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights
reserved.
Copyright (c) 1995-2008 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 4.3 (GENERIC) #696: Thu Mar 6 05:09:01 MST 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD"
586-class) 500 MHz
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX
real mem = 536440832 (511MB)
avail mem = 510664704 (487MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 20/70/03, BIOS32 rev. 0 @ 0xfac40
pcibios0 at bios0: rev 2.0 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc8000/0xa800
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x31
glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
vr0 at pci0 dev 6 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11,
address 00:00:24:c9:a7:30
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x004063, model 0x0034
vr1 at pci0 dev 7 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 5,
address 00:00:24:c9:a7:31
ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x004063, model 0x0034
vr2 at pci0 dev 8 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 9,
address 00:00:24:c9:a7:32
ukphy2 at vr2 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x004063, model 0x0034
vr3 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 12,
address 00:00:24:c9:a7:33
ukphy3 at vr3 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x004063, model 0x0034
vendor "Intel", unknown product 0x1074 (class network subclass ethernet,
rev 0x05) at pci0 dev 14 function 0 not configured
glxpcib0 at pci0 dev 20 function 0 "AMD CS5536 ISA" rev 0x03: rev 0,
32-bit 3579545Hz timer, watchdog, gpio
gpio0 at glxpcib0: 32 pins
pciide0 at pci0 dev 20 function 2 "AMD CS5536 IDE" rev 0x01: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFX3-8192>
wd0: 4-sector PIO, LBA, 7815MB, 16007040 sectors
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2
pciide0: channel 1 ignored (disabled)
ohci0 at pci0 dev 21 function 0 "AMD CS5536 USB" rev 0x02: irq 15,
version 1.0, legacy support
ehci0 at pci0 dev 21 function 1 "AMD CS5536 USB" rev 0x02: irq 15
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1
isa0 at glxpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
nsclpcsio0 at isa0 port 0x2e/2: NSC PC87366 rev 10: GPIO VLM TMS
gpio1 at nsclpcsio0: 29 pins
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom0: console
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1
biomask e5c5 netmask ffe5 ttymask ffe7
mtrr: K6-family MTRR support (2 registers)
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
Automatic boot in progress: starting file system checks.
/dev/rwd0a: file system is clean; not checking
/dev/rwd0h: file system is clean; not checking
/dev/rwd0d: file system is clean; not checking
/dev/rwd0g: file system is clean; not checking
/dev/rwd0e: file system is clean; not checking
setting tty flags
starting network
DHCPREQUEST on vr0 to 255.255.255.255 port 67
DHCPACK from 10.44.0.2
bound to 10.44.1.9 -- renewal in 21600 seconds.
starting system logger
starting initial daemons:.
savecore: /dev/wd0b: Device not configured
checking quotas: done.
building ps databases: kvm dev.
clearing /tmp
starting pre-securelevel daemons:.
setting kernel security level: kern.securelevel: 0 -> 1
creating runtime link editor directory cache.
preserving editor files
starting network daemons: sendmail inetd sshd.
starting local daemons:.
standard daemons: cron.
Tue Aug 28 21:44:35 BST 2007
OpenBSD/i386 (yidhra.outer.uphall.net) (tty00)
login: 00
_______________________________________________
Soekris-tech mailing list
[email protected]
http://lists.soekris.com/mailman/listinfo/soekris-tech
