Top-posting because there's a lot here. Try assigning different ip ranges to the other interfaces and re-test.
Bryan - On Fri, Dec 5, 2008 at 8:39 AM, stef <[EMAIL PROTECTED]> wrote: > Hi, > I just receive on dec 2nd, my new "very expensive box" net5501-70 from > soekris USA. > I boot the net5501 with a 4 Go CF card and voyage-linux 0.5.2 OS > installed in. > My computer based on linux Ubuntu 8.04.1.is linked to the net5501. > BIOS v 133 > > The OS is working good and I made some tests in order to use it as a > router. > But it's impossible to communicate with eth1 eth2 eth3. eth0 is well > working. > > > ------------------------------------------------------------------- > >> first test : work well > [ home PC] ---- eth0 [ net5501] > 192.168.10.1 192.168.10.50 > > soekris:/etc# ping -I eth0 192.168.10.1 > PING 192.168.10.1 (192.168.10.1) from 192.168.10.50 eth0: 56(84) bytes > of data. > 64 bytes from 192.168.10.1: icmp_seq=1 ttl=64 time=0.250 ms > 64 bytes from 192.168.10.1: icmp_seq=2 ttl=64 time=0.174 ms > > [EMAIL PROTECTED]:~$ ping 192.168.10.50 > PING 192.168.10.50 (192.168.10.50) 56(84) bytes of data. > 64 bytes from 192.168.10.50: icmp_seq=1 ttl=64 time=0.242 ms > 64 bytes from 192.168.10.50: icmp_seq=2 ttl=64 time=0.238 ms > 64 bytes from 192.168.10.50: icmp_seq=3 ttl=64 time=0.238 ms > >>>>>>>>>>>>>>>>>>>> OK good > > ------------------------------------------------------------------- > >> second test : > [ home PC] ---- eth1 [ net5501] > 192.168.10.1 192.168.10.51 > > soekris:/etc# ping -I eth1 192.168.10.1 > PING 192.168.10.1 (192.168.10.1) from 192.168.10.50 eth1: 56(84) bytes > of data. > From 192.168.10.50 icmp_seq=2 Destination Host Unreachable > From 192.168.10.50 icmp_seq=3 Destination Host Unreachable > >>>>>>>>>>>>>>> no ping answer from the box net5501 !!! > > [EMAIL PROTECTED]:~$ ping 192.168.10.51 > PING 192.168.10.51 (192.168.10.51) 56(84) bytes of data. > From 192.168.10.1 icmp_seq=2 Destination Host Unreachable > From 192.168.10.1 icmp_seq=3 Destination Host Unreachable > >>>>>>>>>>>>>>> no ping answer from my PC !!! > > soekris:/etc# ping 192.168.10.51 > PING 192.168.10.51 (192.168.10.51) 56(84) bytes of data. > 64 bytes from 192.168.10.51: icmp_seq=1 ttl=64 time=0.191 ms > 64 bytes from 192.168.10.51: icmp_seq=2 ttl=64 time=0.143 ms > >>>>>>>>>>>>>>> only loopback ping on net5501 working > > >> third test : >>>>>>>>>>>>>>>>>>>>> no ping answer !!! > [ home PC] ---- eth2 [ net5501] .... and same for eth3 > > ------------------------------------------------------------------- > here are some tests result on my soekris > > soekris:/# netstat -i -e > Kernel Interface table > eth0 Link encap:Ethernet HWaddr 00:00:24:CB:51:EC > inet addr:192.168.10.50 Bcast:192.168.10.255 Mask:255.255.255.0 > inet6 addr: fe80::200:24ff:fecb:51ec/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:29788 errors:0 dropped:0 overruns:0 frame:0 > TX packets:3404 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:7980048 (7.6 MiB) TX bytes:257892 (251.8 KiB) > Interrupt:11 > > eth1 Link encap:Ethernet HWaddr 00:00:24:CB:51:ED > inet addr:192.168.10.51 Bcast:192.168.10.255 Mask:255.255.255.0 > inet6 addr: fe80::200:24ff:fecb:51ed/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:2590 errors:0 dropped:0 overruns:0 frame:0 > TX packets:468 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:171058 (167.0 KiB) TX bytes:44456 (43.4 KiB) > Interrupt:5 Base address:0x2100 > > eth2 Link encap:Ethernet HWaddr 00:00:24:CB:51:EE > inet addr:192.168.10.52 Bcast:192.168.10.255 Mask:255.255.255.0 > inet6 addr: fe80::200:24ff:fecb:51ee/64 Scope:Link > UP BROADCAST MULTICAST MTU:1500 Metric:1 > RX packets:4 errors:0 dropped:0 overruns:0 frame:0 > TX packets:6 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:362 (362.0 b) TX bytes:468 (468.0 b) > Interrupt:9 Base address:0x6200 > > eth3 Link encap:Ethernet HWaddr 00:00:24:CB:51:EF > inet addr:192.168.10.53 Bcast:192.168.10.255 Mask:255.255.255.0 > UP BROADCAST MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) > Interrupt:12 Base address:0x8300 > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 Scope:Host > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:46560 errors:0 dropped:0 overruns:0 frame:0 > TX packets:46560 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:5214270 (4.9 MiB) TX bytes:5214270 (4.9 MiB) > > soekris:/etc# route -n > Kernel IP routing table > Destination Gateway Genmask Flags Metric Ref Use > Iface > 192.168.10.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 > 192.168.10.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 > 192.168.10.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 > 192.168.10.0 0.0.0.0 255.255.255.0 U 0 0 0 eth3 > 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo > 0.0.0.0 192.168.10.9 0.0.0.0 UG 0 0 0 eth0 > > > dmesg result : > ... > via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker > eth0: VIA Rhine III (Management Adapter) at 0xa0004000, > 00:00:24:cb:51:ec, IRQ 11. > eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 45e1. > eth1: VIA Rhine III (Management Adapter) at 0xa0004100, > 00:00:24:cb:51:ed, IRQ 5. > eth1: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000. > eth2: VIA Rhine III (Management Adapter) at 0xa0004200, > 00:00:24:cb:51:ee, IRQ 9. > eth2: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000. > eth3: VIA Rhine III (Management Adapter) at 0xa0004300, > 00:00:24:cb:51:ef, IRQ 12. > eth3: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000. > ... > > > soekris:/etc# iptables -L > Chain INPUT (policy ACCEPT) > target prot opt source destination > > Chain FORWARD (policy ACCEPT) > target prot opt source destination > > Chain OUTPUT (policy ACCEPT) > target prot opt source destination > > ------------------------------------------------------------------- > > I try several ethernet cables for the second test but still impossible > to communicate by eth1 eth2 eth3. > No problems found in : iptables, route, dmesg, ifconfig. > Where is the bug ? > > Only eth0 is perfectly working. So perfectly thah I had upgraded the OS > with apt-get command when linked to Internet by eth0, no link problem. > > Would you help me in configuring eth1 2 3, > I think it's a material problem !!! but not really sure ... > > Thanks > _______________________________________________ > Soekris-tech mailing list > [email protected] > http://lists.soekris.com/mailman/listinfo/soekris-tech > _______________________________________________ Soekris-tech mailing list [email protected] http://lists.soekris.com/mailman/listinfo/soekris-tech
