Exactly. 2 to 15 minutes to get water to monitors is not acceptable. Also, the torsion required on the PI shaft and shear strength of any cotter pins would approach number on the order of what $$$ I evidently owe the government to pay for all the stimulus and bailout programs.
Ryan Hinson Burns & McDonnell Direct: 952-656-6003 Ext 3662 -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Autry, David Sent: Wednesday, September 23, 2009 3:41 PM To: [email protected] Subject: RE: Post Indicators Understand. If you do find and go with some sort of gear arrangement, it might take more than 5 seconds. :-) David Autry Plans Examiner Nebraska State Fire Marshal's Office 246 S. 14th Street Lincoln, NE 68508 402-471-9659 402-471-3118 fax www.sfm.ne.gov ** Note new email address: [email protected] -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Hinson, Ryan Sent: Wednesday, September 23, 2009 3:38 PM To: [email protected] Subject: RE: Post Indicators We have included that argument among others. This is not the first issue we've had with them regarding what the codes and standards as they are their own approving jurisdiction. Ryan Hinson Burns & McDonnell Direct: 952-656-6003 Ext 3662 -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Autry, David Sent: Wednesday, September 23, 2009 3:33 PM To: [email protected] Subject: RE: Post Indicators Can't use ball valves per NFPA 24 (2002, Edition) 6.1.2 Indicating valves shall not close in less than 5 seconds when operated at maximum possible speed from the fully open position. David Autry Plans Examiner Nebraska State Fire Marshal's Office 246 S. 14th Street Lincoln, NE 68508 402-471-9659 402-471-3118 fax www.sfm.ne.gov ** Note new email address: [email protected] -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Hinson, Ryan Sent: Wednesday, September 23, 2009 3:27 PM To: [email protected] Subject: Post Indicators Does anyone know of a post indicator that can be used in conjunction with a 12" ball valve installed below grade? I've been trying to find one at the request of a customer for use as control valves for the underground firewater piping of an industrial facility. We've gone around and around ad nauseam but they don't want butterfly or gate valves because in their words they, "don't want to dig up the valve when it no longer seals". Ball valves that size normally require a ~3' long handle and show the handle almost directly fastened to the valve body itself. Gearboxes could be used at valve level, but I still need to extend the handle of the gearbox above grade in such a way as to indicate the valve position. Anyone out there with any experience with this scenario? Ryan L. Hinson, EIT, NICET III Fire Protection Systems Designer, Aviation and Facilities Group Minneapolis-St. Paul Office Burns & McDonnell 8201 Norman Center Drive, Suite 300 Bloomington, MN 55437 Direct: 952-656-6003 Ext 3662 Fax: 952-229-2923 www.burnsmcd.com <BLOCKED::www.burnsmcd.com> Proud to be one of FORTUNE's 100 Best Companies To Work For _______________________________________________ Sprinklerforum mailing list [email protected] http://fireball.firesprinkler.org/mailman/listinfo/sprinklerforum For Technical Assistance, send an email to: [email protected] To Unsubscribe, send an email to:[email protected] (Put the word unsubscribe in the subject field) _______________________________________________ Sprinklerforum mailing list [email protected] http://fireball.firesprinkler.org/mailman/listinfo/sprinklerforum For Technical Assistance, send an email to: [email protected] To Unsubscribe, send an email to:[email protected] (Put the word unsubscribe in the subject field) _______________________________________________ Sprinklerforum mailing list [email protected] http://fireball.firesprinkler.org/mailman/listinfo/sprinklerforum For Technical Assistance, send an email to: [email protected] To Unsubscribe, send an email to:[email protected] (Put the word unsubscribe in the subject field) _______________________________________________ Sprinklerforum mailing list [email protected] http://fireball.firesprinkler.org/mailman/listinfo/sprinklerforum For Technical Assistance, send an email to: [email protected] To Unsubscribe, send an email to:[email protected] (Put the word unsubscribe in the subject field) _______________________________________________ Sprinklerforum mailing list [email protected] http://fireball.firesprinkler.org/mailman/listinfo/sprinklerforum For Technical Assistance, send an email to: [email protected] To Unsubscribe, send an email to:[email protected] (Put the word unsubscribe in the subject field)
