This sound like a good question to be answered not only by the AHJ, but the owner and their insurance carrier since it is their money that is on the line.
-- Craig Leadbetter Safeguard of Marquette PO Box 116 Marquette, MI 49855 (O) 906-475-9955 (F) 906-475-5474 (C) 906-362-5393 [email protected] On Thu, Jan 17, 2013 at 2:13 PM, Bill Brooks <[email protected]>wrote: > But here's a follow-up question - who is the appropriate individual to make > this determination? In my opinion this is not the sprinkler contractor. > Please read the word "not" as if I had capitalized it. > > Just my opinion. > > Bill Brooks > > William N. Brooks, P.E. > Brooks Fire Protection Engineering Inc. > 372 Wilett Drive > Severna Park, MD 21146-1904 > 410-544-3620 > 410-544-3032 FAX > 412-400-6528 Cell > > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Cahill, > Christopher > Sent: Thursday, January 17, 2013 1:11 PM > To: [email protected] > Subject: RE: Replacing heads after a fire > > 2 is all required in your example, well if you want to return to service. > > The heat cooling cycle of the glass bulbs are repeated cycles to very near > operating temperature as I understand it. One more cycle if it takes 100's > or more cycles won't make a difference. The first 99 are the problem. > > On the creep of solder its sustained temperatures near operation as I > understand it. This is a problem not a single fire. > > On the acid - well smoke comes in all flavors. I'm certainly no chemist > but > with that logic why are we not replacing the structural components or the > plumbing etc.? Weren't they also damaged by the acid smoke? I think where > acid is an issue is in sensitive electronics. Think of the difference in > surface area. And I don't understand the burn/smoke radius part. The > burn > radius of a sprinkler controlled fire is on the order of 1 to ten's of > feet. > The smoke is often the entire building. Not sure you need to go next door > and replace sprinkler head to get 2 rings past, lol. > > What I typically see is out of an abundance of caution replace the fused > heads and the first ring around. But I don't think it has any technical > merit. Once the fitter is there a couple more heads is cheap to make > everyone feel good. In the end I wouldn't balk if you replace the 2 and if > someone pays you for more, good for you. > > Good discussion item. Often we don't get truly new things to banter about > on this forum. > > Chris Cahill, PE* > Senior Fire Protection Engineer, Aviation & Facilities Group Burns & > McDonnell > 8201 Norman Center Drive > Bloomington, MN 55437 > Phone: 952.656.3652 > Fax: 952.229.2923 > [email protected] > www.burnsmcd.com > > Proud to be one of FORTUNE's 100 Best Companies to Work For *Registered in: > MN > > > > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Ben Young > Sent: Thursday, January 17, 2013 11:41 AM > To: [email protected] > Subject: Replacing heads after a fire > > This was a hypothetical question asked by one of our inspectors the other > day, and I did not know the answer. Thought I would see if anyone else > here > might know where this is written in black and white. > > Say you have a large room with 20+ heads, or an open warehouse area. The > building is fully sprinkled, and everything else is normal / SOP. > > They have a fire in this room/area, and lets say, two heads activate and > control the fire. > > The question is, how many of the heads do you have to replace? Is there a > code requirements for this that exists? I found some anecdotal evidence > from someone in the industry with more experience than I, but the only > thing > close I could find in the codes was the NFPA 25 stuff relating to loading > on > sprinkler heads. > > I looked at NFPA's list of codes online, and saw some that may have some > information on this (NFPA 902 and 904) but they were withdrawn in 2001, and > I cannot view them online. > > Obviously from a liability standpoint, you would want to replace as many of > the heads as possible, if not all of them, but what if you had a 500K SQFT > warehouse that was all open, would you want to replace all of them? > > Here's the information that I got from my friend who's been around a while. > -If they're link heads, you want to probably replace all the heads, since > the acids in the smoke will impact the solder -Look at the burn/smoke > radius > from the fire, and replace the heads around this area for the next two > rings > of sprinkler heads. > > He couldn't tell me where this came from, it was just the way it was always > done. > > Is there a hard and fast rule for this? Is it an insurance carrier or head > manufacturer judgement call? Would rapid heating and cooling cause glass > bulbs to weaken or micro-fracture down the road? > > > Thanks, > > > Benjamin Young > -------------- next part -------------- > An HTML attachment was scrubbed... > URL: > < > http://fireball.firesprinkler.org/mailman/private/sprinklerforum/attachment > s/20130117/93248633/attachment.html> > _______________________________________________ > Sprinklerforum mailing list > [email protected] > http://fireball.firesprinkler.org/mailman/listinfo/sprinklerforum > _______________________________________________ > Sprinklerforum mailing list > [email protected] > http://fireball.firesprinkler.org/mailman/listinfo/sprinklerforum > > _______________________________________________ > Sprinklerforum mailing list > [email protected] > http://fireball.firesprinkler.org/mailman/listinfo/sprinklerforum > -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://fireball.firesprinkler.org/mailman/private/sprinklerforum/attachments/20130117/f741fe5c/attachment.html> _______________________________________________ Sprinklerforum mailing list [email protected] http://fireball.firesprinkler.org/mailman/listinfo/sprinklerforum
