Dear user and developers,
I have few question about density output that how does density in
SUMO calculate ? I mean that SUMO program is calculated by approximation
with travel-time or count the vehicle in specified edge or others ? I want
some information because i would use it in some macroscopic model. Thank
you
Best regards,
Jirayu Tippayagulpairod
2017-02-09 9:20 GMT+07:00 Jirayu Tippayagulpairod <[email protected]>:
> Thank you very much. It's helped me a lot
>
> 2017-02-08 22:39 GMT+07:00 Jakob Erdmann <[email protected]>:
>
>> yes. (don't forget the quotes)
>> vTypes="bus"
>>
>> 2017-02-08 9:09 GMT+01:00 Jirayu Tippayagulpairod <[email protected]>
>> :
>>
>>> Oh thank you very much, It means that you use this for example
>>> <edgeData id="<MEASUREMENT_ID>" file="<OUTPUT_FILE>" vTypes = bus/>
>>> and import this as additional file before simulation , am i right ?
>>>
>>> Best regards,
>>> Bank
>>>
>>> 2017-02-07 14:08 GMT+07:00 Jakob Erdmann <[email protected]>:
>>>
>>>> Yes, the metrics you require will be available separately for each of
>>>> the types you select (see http://sumo.dlr.de/wiki/Simula
>>>> tion/Output/Lane-_or_Edge-based_Traffic_Measures#Value_Descriptions).
>>>> By setting a different value for the output 'file' attribute for each type,
>>>> it is easy to process them separately as well.
>>>> regards,
>>>> Jakob
>>>>
>>>> 2017-02-06 9:10 GMT+01:00 Jirayu Tippayagulpairod <
>>>> [email protected]>:
>>>>
>>>>> Thank you for your suggestion. But i still have some confused that if
>>>>> i generate the output via edge data , Could I export the output that I
>>>>> mentioned before (edge performance e.g. density and traveltime ) I
>>>>> apologize for any misunderstanding .I am some beginner in SUMO
>>>>>
>>>>> Best regards,
>>>>>
>>>>> Jirayu
>>>>>
>>>>> 2017-02-06 13:49 GMT+07:00 Jakob Erdmann <[email protected]>:
>>>>>
>>>>>> When using simulated induction loops (http://sumo.dlr.de/wiki/Simul
>>>>>> ation/Output/Induction_Loops_Detectors_(E1)) you can set the
>>>>>> attribute splitByType="true" to get type-specific output.
>>>>>>
>>>>>> When using edgeData (http://sumo.dlr.de/wiki/Simul
>>>>>> ation/Output/Lane-_or_Edge-based_Traffic_Measures) you can filter
>>>>>> for type by setting the vTypes attribute (i.e. vTypes="bus"). You will
>>>>>> then
>>>>>> need a separate <edgeData>-definitions for each type (or list of types)
>>>>>> you
>>>>>> are interested in.
>>>>>>
>>>>>> regards,
>>>>>> Jakob
>>>>>>
>>>>>> 2017-02-03 2:33 GMT+01:00 Jirayu Tippayagulpairod <
>>>>>> [email protected]>:
>>>>>>
>>>>>>> Dear user and developers ,
>>>>>>> I'm student in Thailand who do the project with SUMO
>>>>>>> program and I have some question to ask. As I used SUMO , it can
>>>>>>> simulate
>>>>>>> the many type of vehicle in traffic and the
>>>>>>> output is in form of enter , left ,density , travel time but it
>>>>>>> doesn't
>>>>>>> show each type of output (For example : I mean that 4 outputs for
>>>>>>> car and 4
>>>>>>> outputs for bus individually) Therefore, I want to know that Can SUMO
>>>>>>> simulate the outputs individually for each type of vehicles or it
>>>>>>> cannot ?
>>>>>>>
>>>>>>> Best regards,
>>>>>>>
>>>>>>> Jirayu Tippayagulpairod
>>>>>>> ------------------------------------------------------------
>>>>>>> ------------------
>>>>>>> Check out the vibrant tech community on one of the world's most
>>>>>>> engaging tech sites, SlashDot.org! http://sdm.link/slashdot
>>>>>>> _______________________________________________
>>>>>>> sumo-user mailing list
>>>>>>> [email protected]
>>>>>>> https://lists.sourceforge.net/lists/listinfo/sumo-user
>>>>>>>
>>>>>>
>>>>>>
>>>>>
>>>>
>>>
>>
>
------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, SlashDot.org! http://sdm.link/slashdot
_______________________________________________
sumo-user mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/sumo-user
