Hi, Generally a lot of common problems with installation and configuration have been adressed at some point on this list. Searching the archives is always a good idea. Remember that most of the time what is valid for RHEL is valid for CentOS.
One thing comes to mind: - remember to not have network name in /etc/hosts that is mapped to both 127.0.0.1 and the an adress on the subnet you want to run SRSS on (for utadm -A) configurations. Also, trying this ou in a virtual machine, where you can take snapshots and roll back if you do something that doesn't work, is a good idea. Good luck, Øystein > Hello, > > To follow-up with the group. Friday I did the install again of SRSS 4.1. > Install pdksh, install SRSS4.1 reboot. No authentication problems! On > with > the config. Are there any other resources other than documentation that > can > be referenced in the config. At the moment standalone, looks pretty > straightforward. Any suggestions are welcome. > > Cheers, > M > > On Fri, Feb 27, 2009 at 9:06 AM, shambalad <[email protected]> wrote: > >> Hi Brad, >> >> I wanted to get back to the group earlier yesterday but was unable. >> Thanks >> for getting back to me. I believe it has something to do with SRSS. I >> am >> not sure as well. Unfortunately I cannot take the time to debug this >> fully. I had another configuration available installed pdksh and no >> problem. Sometime this afternoon, SRSS will be back in the picture. >> I'll >> keep you posted. >> >> Cheers, >> M >> >> >> On Thu, Feb 26, 2009 at 11:32 AM, Brad Lackey - US-SW Desktop >> Virtualization Technology Lead <[email protected]> wrote: >> >>> It's important to install the Sun supplied pdksh before installing and >>> configuring SRSS. You will additionally need the extra packages listed >>> in >>> the Release Notes. >>> >>> I'm not sure why swapping out one shell for another would cause the >>> authentication failure. It shouldn't. If you boot into single user >>> mode, and >>> change the shell for the user you are using to bash, does it let you >>> log-in? >>> >>> Brad >>> >>> >>> On Feb 26, 2009, at 8:10 AM, shambalad wrote: >>> >>> Hello, >>>> >>>> By default KSH was the login shell for the account. I had already >>>> install SRSS 4.1 on the server and was preparing to setup the DTU to >>>> connect. I saw the post related to the subject that pdksh should be >>>> used. >>>> I removed ksh -- No errors >>>> I installed pdksh -- No errors (should I have done something else?) >>>> rebooted. >>>> At login screen window pops up 'Authentication Failed' cannot login. >>>> I >>>> did not go to log files as of yet. Restored machine from backup. >>>> Any thoughts... Must I do/verify something? >>>> >>>> Thanks for assistance, >>>> M >>>> >>>> On Thu, Feb 26, 2009 at 11:00 AM, <[email protected]> wrote: >>>> > Hello All, >>>> > >>>> > I am currently attempting to install pdksh on a Centos 5.2 i386 >>>> install. >>>> > I >>>> > have not yet configured a SunRay DTU to connect currently setting up >>>> a >>>> > standalone, I have been following documentation closely . I came >>>> across a >>>> > post related to utconfig failing on RHEL 5.2 the privately compiled >>>> > version >>>> > of Centos 5.2. In either case in preparation I cannot log into my >>>> server >>>> > after(get authentication failing window after reboot at login >>>> window): >>>> > yum remove ksh >>>> > then install pdksh from supplemental folder on SRSS 4.1 >>>> > Is this necessary? If so any idea? >>>> >>>> Hi, it's a bit unclear what your problem really is, but yes, in my >>>> experience it is necessary to replace ksh with pdksh, or else utconfig >>>> fails (from an earlier post on this list, no explanation as to why >>>> this >>>> works). >>>> >>>> I don't see any reason for this making it impossible to log in? Have >>>> you >>>> set ksh as the login shell for root or something similar? >>>> >>>> HTH, >>>> Øystein >>>> >>>> _______________________________________________ >>>> SunRay-Users mailing list >>>> [email protected] >>>> http://www.filibeto.org/mailman/listinfo/sunray-users >>>> >>>> _______________________________________________ >>>> SunRay-Users mailing list >>>> [email protected] >>>> http://www.filibeto.org/mailman/listinfo/sunray-users >>>> >>> >>> >>> Brad Lackey >>> Desktop Virtualization Technology Lead >>> US Software Practice >>> (720) 548-3339 >>> >>> >>> >>> >>> >>> _______________________________________________ >>> SunRay-Users mailing list >>> [email protected] >>> http://www.filibeto.org/mailman/listinfo/sunray-users >>> >>> >> > _______________________________________________ > SunRay-Users mailing list > [email protected] > http://www.filibeto.org/mailman/listinfo/sunray-users > _______________________________________________ SunRay-Users mailing list [email protected] http://www.filibeto.org/mailman/listinfo/sunray-users
