You shouldn't have had to edit the .parms file. The utfwadm command you
executed should have updated it for you.
Your problem is that you still have DHCP configured, and the values in there are not
updated and they're taking precedence over the .parms values. That's because you ran
"utfwadm -N all" previously with the old firmware files.
Try doing "svcadm disable dhcp-server", and then doing the "utfwload -L"
command again.
-Bob
On 06/26/11 04:27 PM, Kalle Anka wrote:
I edited the file SunRay8.parms file to the new FW version (as Arthurpeck
suggested):
version=4.3_146928-01_2011.06.03.14.41
revision=3
barrier=430
And then I did
# /opt/SUNWut/sbin/utfwadm -A -a -V -f
Components/10-SRSS/Patches/solaris/sparc/146928-01/SUNWutfw/reloc/SUNWut/lib/firmware
CoronaP1 4.3_146928-01_2011.06.03.14.41
SunRayP10 4.3_146928-01_2011.06.03.14.41
CoronaP2 4.3_146928-01_2011.06.03.14.41
CoronaP3 4.3_146928-01_2011.06.03.14.41
CoronaP4 4.3_146928-01_2011.06.03.14.41
CoronaP5 4.3_146928-01_2011.06.03.14.41
CoronaP6 4.3_146928-01_2011.06.03.14.41
CoronaP7 4.3_146928-01_2011.06.03.14.41
SunRayP8 4.3_146928-01_2011.06.03.14.41
SunRayP9 4.3_146928-01_2011.06.03.14.41
And then I did
# /opt/SUNWut/sbin/utfwload -L
Upgrading units to version 4.3_146928-01_2011.06.03.14.41:
11.0 gdm 192.168.1.2 P8.00144f946b02 4.3_50_2011.04.22.22.07
And something happened. The SunRay2 DTU rebooted and it said:
Decompressing file
Verifying Signature
Erasing Flash, DO NOT POWER OFF!
Programming flase, DO NOT POWER OFF
And now:
# /opt/SUNWut/sbin/utquery 192.168.1.2
terminalID=00144f946b02
terminalIPA=192.168.1.2
model=SunRayP8
currentAuth=192.168.1.3
currentFW=4.3_50_2011.04.22.22.07
currentBarrier=430
currentBarrierLevel=430
currentMTU=1500
currentLease=49176
Subnet=255.255.255.0
Router=192.168.1.1
MTU=1500
LeaseTim=49185
DHCPServer=192.168.1.1
INFORMServer=192.168.1.3
AuthSrvr=192.168.1.3
AuthPort=7009
LogHost=192.168.1.3
FwSrvr=192.168.1.3
NewTVer=4.3_50_2011.04.22.22.07
FWservType=FWSrvr
speed=100F
parmsVersion=4.3_50_2011.04.22.22.07
parmsBarrier=430
configMTU=1500
AltAuth=192.168.1.3
dnsList=192.168.1.1
confEnabled=1
confNetType=DHCP
conf.kbcountry=26
kbcountry=26
stopqon=0
bandwidth=100000000
cmdcachesize=512
It is still the same old firmware. But maybe stale parms file in /tftpboot could
be the culprit.
So, what now? Should I edit every "parms" file? Why should I only edit the
SunRayP8.parms file, why not SunRayP9.parms too?
Or, should I copy all files as Craig suggested:
"copy the contents of
Components/10-SRSS/Patches/solaris/sparc/146928-01/SUNWutfw/reloc/SUNWut/lib/firmware
to /opt/SUNWut/lib/firmware"
I am closer to the solution!
_______________________________________________
SunRay-Users mailing list
[email protected]
http://www.filibeto.org/mailman/listinfo/sunray-users
