Hello Oleg, Question: does the software needs to reach the 34VL02 EEPROM at any point? Because I don't have one on my own sensor board...
Fred On Thu, Mar 8, 2018 at 4:11 PM, Frederick Gamache < frederick.gama...@gmail.com> wrote: > Thanks a lot! > > I will make some tests and I'll keep you posted. > > Regards, > Fred > > On Thu, Mar 8, 2018 at 4:09 PM, Oleg <support-list@support.elphel.com> > wrote: > >> Frederick, >> >> 1. Here are the files: https://community.elphe >> l.com/files/393/20180308_test_0x5d/ >> >> 2. Before copying - boot from the card and check the linux version: >> >>> root@elphel393:~# uname -r >>> 4.9.0-xilinx-v2017.3 >> >> >> * If it's 4.9.0-xilinx-v2017.3 then copying only devicetree.dtb and >> uImage might be enough - they are on the FAT partition of the card. >> * In case of fail if you use minicom (or putty or other serial terminal >> program) there will be some kind of a kernel panic. >> >> 3. >> My bootlog for 0x5d: >> >>> ... >>> [ 21.692018] {0} Setting i2c_addr to 0x5d >>> [ 21.696039] Read i2c (port = 0, sa7=0x5d, reg=0x0) chip ID=ffff >>> ... >>> [ 21.747074] {1} Setting i2c_addr to 0x5d >>> [ 21.756495] Read i2c (port = 1, sa7=0x5d, reg=0x0) chip ID=ffff >>> ... >>> [ 21.807904] {2} Setting i2c_addr to 0x5d >>> [ 21.817282] Read i2c (port = 2, sa7=0x5d, reg=0x0) chip ID=ffff >>> ... >>> [ 21.868874] {3} Setting i2c_addr to 0x5d >>> [ 21.878291] Read i2c (port = 3, sa7=0x5d, reg=0x0) chip ID=ffff >> >> ... >> >> >> bootlog for 0x48 (2 sensors connected): >> >>> ... >> >> [ 21.607985] {0} Setting i2c_addr to 0x48 >>> [ 21.612007] Read i2c (port = 0, sa7=0x48, reg=0x0) chip ID=1801 >>> [ 21.617888] Found MT9P001 2592x1944 sensor, chip ID=1801 >>> [ 21.674977] {1} Setting i2c_addr to 0x48 >>> [ 21.684454] Read i2c (port = 1, sa7=0x48, reg=0x0) chip ID=1801 >>> [ 21.690690] Found MT9P001 2592x1944 sensor, chip ID=1801 >>> [ 21.747575] {2} Setting i2c_addr to 0x48 >>> [ 21.757033] Read i2c (port = 2, sa7=0x48, reg=0x0) chip ID=ffff >>> ... >>> [ 21.808291] {3} Setting i2c_addr to 0x48 >>> [ 21.817738] Read i2c (port = 3, sa7=0x48, reg=0x0) chip ID=ffff >>> ... >> >> >> Best regards, >> Oleg Dzhimiev >> Electronics Engineer >> phone: +1 801 783 5555 x124 <(801)%20783-5555> >> Elphel, Inc. >> > >
_______________________________________________ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
