Thanks for the quick reply.
I have been trying to rebuild using the tigervnc source RPM with the
xorg-x11-server-source RPM also installed.
I am following the instructions from the BUILDING.txt file, but I continue
to get the following error
configure.ac:35: error: must install xorg-macros 1.10 or later before running
autoconf/autogen
Thanks
Don
________________________________
From: Brian Hinz <bph...@users.sourceforge.net>
To: Don M <dmj_1...@yahoo.com>
Cc: "tigervnc-users@lists.sourceforge.net"
<tigervnc-users@lists.sourceforge.net>
Sent: Thursday, June 27, 2013 2:28 PM
Subject: Re: [Tigervnc-users] libvnc.so module not working well in RHEL 6.2
Do you mean that the Xorg module from the EL6 x86_64 RPMs from the nightly
build page does not load? I have not tested the Xorg module myself... If it's
because the build was created with a newer version of Xorg, then you might
simply be able to rebuild the source RPM.
-brian
On Thu, Jun 27, 2013 at 2:07 PM, Don M <dmj_1...@yahoo.com> wrote:
I agree one of the newer pre-releases would work better.
>But, I they don't work out of the box in the setup I need.
>The system that we are connecting to, the OS is already set.
>With the Xorg being version 1.10.4
>1.0.90, is the tigervnc-server-module that ships with RHEL 6.2 64 bit
>which contains that Xorg.
>If I use a new libvnc.so module, the module does not load.
>
>
>
>________________________________
> From: Brian Hinz <bph...@users.sourceforge.net>
>To: Don M <dmj_1...@yahoo.com>
>Cc: "tigervnc-users@lists.sourceforge.net"
><tigervnc-users@lists.sourceforge.net>
>Sent: Tuesday, June 25, 2013 9:47 PM
>Subject: Re: [Tigervnc-users] libvnc.so module not working well in RHEL 6.2
>
>
>
>1.0.90 is pretty old, perhaps one of the new pre-release builds will work
>better:
>
>
>http://tigervnc.sourceforge.net/tiger.nightly/
>
>
>-brian
>
>
>On Tue, Jun 25, 2013 at 10:35 AM, Don M <dmj_1...@yahoo.com> wrote:
>
>Using the following module
>>tigervnc-server-module-1.0.90-0.17.20110314svn4359.el6.x86_64
>>on RHEL 6.2 64 bit system, when the xorg file is modified to use the vnc
>>module.
>>
>>Then connect a VNC Viewer to the display. The display gets very sluggish.
>>It begins to take up to 30 seconds for mouse clicks to go through.
>>If you look at top, the CPU is spinning up to 100%.
>>What are my options, I really need to be able to connect to this system
>>using the xorg's vnc module?
>>
>>
>>ThanksDon
>>------------------------------------------------------------------------------
>>This SF.net email is sponsored by Windows:
>>
>>Build for Windows Store.
>>
>>http://p.sf.net/sfu/windows-dev2dev
>>_______________________________________________
>>Tigervnc-users mailing list
>>Tigervnc-users@lists.sourceforge.net
>>https://lists.sourceforge.net/lists/listinfo/tigervnc-users
>>
>>
>
>
>
------------------------------------------------------------------------------
This SF.net email is sponsored by Windows:
Build for Windows Store.
http://p.sf.net/sfu/windows-dev2dev
_______________________________________________
Tigervnc-users mailing list
Tigervnc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/tigervnc-users
