Said, Interesting thought. I had not considered the TBolt to be a source of a problem.
I also have two HP 58517A 8 way splitters, one that gets it's DC for the antenna through an SMB connector and one that gets it's DC from port 1. They seem to work fine with the TBolt. I also have a Symmetricom 090-58537-01 4 way splitter and it works fine with the TBolt as well. By this, I mean place the splitter between the TBolt and the antenna with nothing else connected. When I do this with the 58535A or 58536A, signal amplitudes, as noted on TBoltMon, are divided in two with the 2 way splitter and non existent with the 4 way splitter. I fired up my Z3816A, hooked it directly to the antenna and all was fine with good signal amplitudes as noted on SatStat. I then put the splitter in the circuit and, again, all was fine. I then hooked up the TBolt to another port of the splitter and, now, it too is fine. Seems it is all OK as long as the Z3816A is connected. I tried substituting a 50 ohm load on the ports but the TBolt problem came back. Might this be insufficient current for the amplifier and antenna from the TBolt? The 'Antenna Open' and 'Antenna Short' indications on TBoltMon are fine no matter how or what is connected. With the TBolt connected, I get about 4.5 VDC to the antenna from the splitter. I forgot to measure with the Z3816A connected. Thanks for the insight. My formerly thought dead splitters are, in fact, fine. I'll have to try adding an external supply to the splitter and see if that fixes the problem. Then, again, if just using the TBolt alone, why have a splitter? I guess the answer is that it is nice to have an easily available connection for other projects. Thanks again everyone for all the help. Joe -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of [email protected] Sent: Saturday, October 31, 2009 10:20 PM To: [email protected] Subject: Re: [time-nuts] HP/Symmetricom 58535A and 58536A Hi Joe, I have the same problem with my Thunderbolt even though my splitter works well. Not sure why. This is especially so if I cascade the Agilent unit with a passive splitter, I can never get the Thunderbolt to lock up. I think the added noise of the Amp may play funny with the Thunderbolt's receiver, and there may not be anything wrong with your splitter. M12M's and uBlox receiver's don't have a problem at all, even if two units are cascaded. They do start to have issues with three splitters in series. Do you have another receiver you can try? In terms of schematics, it's really straight forward, see the Mini-circuits website for sample schematics for the ERA part, the agilent unit has pretty much the same setup. The amp is followed by a resistive splitter, and possibly a resistive attenuator (on the 2-port version). Then a cavity filter, then the N-Connector, very simple, not much that can go wrong. bye, Said In a message dated 10/31/2009 18:21:16 Pacific Daylight Time, [email protected] writes: Said, Thanks for the reply. This is certainly a starting point. A schematic would be wonderful. I have looked and have not found one yet. The units both provide about 4.5 VDC to the center pin when any port is connected to my Tbolt. However, the signal amplitude, as measured by TBoltMon, is essentially non existent on the 4 way splitter and divided by at least 2 on the 2 way splitter. Therefore, I suspect the amplifier is dead. Did not know about the voltage regulator. Will open one and get to work. Thanks, Joe _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
