Hi The closest thing I could find were the side adjust parts. They also have "flat on the board" parts and 3/8" squares. No sign of top adjust 1/4" parts ....
Bob On Jul 7, 2010, at 1:09 AM, Ed Palmer wrote: > It looks like there's still a problem with the trimmers. R17 and R22 are > shown as part # 3266P-1-502LF and the photo shows the proper type of trimmer. > The data sheet and the catalog page show that 3266P has the adjustment > parallel to the board rather than vertical. Mouser just used the same > picture for all styles of the 3266 line. There are others that are in stock, > but they're larger and I don't know if there's room for them on the board. > > Ed > > Bob Bownes wrote: >> Changed it to a different part that is available. Difference is RHoS >> compliance method. >> >> Changed the backordered 2n3906 as well. Shaved $0.02 off the total cost! >> >> Bob >> >> >> On Fri, Jul 2, 2010 at 3:17 PM, Bob Camp <[email protected]> wrote: >> >>> Hi >>> >>> It looks like it may be a while before the trim pots come in (12 weeks...). >>> The 3266X (side adjust rather than top adjust) is in stock. I'm not sure if >>> the layout is "side adjust" friendly or not. >>> >>> Bob >>> >>> -----Original Message----- >>> From: [email protected] [mailto:[email protected]] On >>> Behalf Of Bob Bownes >>> Sent: Friday, July 02, 2010 2:54 PM >>> To: Discussion of precise time and frequency measurement >>> Subject: Re: [time-nuts] Pic programing for the PICTIC II >>> >>> Folks, >>> >>> I put together a mouser 'project' with all of the parts. This means >>> you can just go to the mouser site and order all the parts for the >>> project. No need for anyone to do a group buy of parts, re-pack and >>> re-distribute them. Here's how to get to it: >>> >>> To access the project, click on the url listed below or copy and paste >>> it into your web browser: >>> >>> http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=c7ada9ced0 >>> >>> Or you can access the project by going to http://www.mouser.com/ and >>> click on the EZ Buy option on the top navigation bar. You can also >>> click on this link or copy and paste it into your browser: >>> http://www.mouser.com/Tools/Tools.aspx. Then enter the following >>> access number listed below into the Project Access ID function. >>> >>> c7ada9ced0 >>> >>> >>> Total cost w/o shipping is $30.30. >>> >>> >>> On Fri, Jul 2, 2010 at 1:23 PM, Peter Vince <[email protected]> wrote: >>> >>>> Apologies for the previous incomplete message - somehow my laptop >>>> trackpad jumped the cursor over the send button :-( >>>> >>>> >>>>> Better ? >>>>> How many16f688s are we talking here? >>>>> >>>>> My thinking is less than 10 as only two people have asked. >>>>> Don't know how many have not asked. >>>>> >>>> I would also like a pre-programmed PIC please, if someone can arrange >>>> that. Or ideally, a complete kit of parts, but as the previous >>>> correspondent has written, I appreciate that is a lot of work. >>>> >>>> Thanks, >>>> >>>> Peter Vince (London, England) >>>> >>>> _______________________________________________ >>>> time-nuts mailing list -- [email protected] >>>> To unsubscribe, go to >>>> >>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >>> >>>> and follow the instructions there. >>>> >>>> >>> _______________________________________________ >>> time-nuts mailing list -- [email protected] >>> To unsubscribe, go to >>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >>> and follow the instructions there. >>> >>> >>> >>> >>> _______________________________________________ >>> time-nuts mailing list -- [email protected] >>> To unsubscribe, go to >>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >>> and follow the instructions there. >>> >>> >> >> _______________________________________________ >> time-nuts mailing list -- [email protected] >> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >> and follow the instructions there. >> >> > > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
