Hi I strongly recommend checking your local inventory (dare I say junk box.) off a lot of the parts. Stuff like bypass caps likely something you have.
Bob On Aug 7, 2010, at 5:10 AM, Steve Rooke <[email protected]> wrote: > Hi Bob, > > I have the correct DIL 74175 so I can untick that item. > > Steve > > On 07/08/2010, Bob Camp <[email protected]> wrote: >> Hi >> >> As far as I know all the parts are correct except the 74175. It is the soic >> version. >> >> Bob >> >> >> >> On Aug 6, 2010, at 7:16 PM, Steve Rooke <[email protected]> wrote: >> >>> Bob, >>> >>> Thanks for that, this Mouser project has all available parts. Do you >>> know if the pots, trimmers, etc. are ones as suggested for the correct >>> orientation, pin spacing, etc. as i believe there was some discussion >>> regarding this in among the many postings on this topic? >>> >>> Steve >>> >>> On 07/08/2010, Bob Camp <[email protected]> wrote: >>>> Hi >>>> >>>> I believe the project at: >>>> >>>> http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=8736DCEE10 >>>> >>>> is up to date in (no un-orderable parts). >>>> >>>> Bob >>>> >>>> -----Original Message----- >>>> From: [email protected] [mailto:[email protected]] On >>>> Behalf Of Didier Juges >>>> Sent: Friday, August 06, 2010 8:36 AM >>>> To: 'Discussion of precise time and frequency measurement' >>>> Subject: Re: [time-nuts] What's the latest correct PICTIC II Mouser >>>> project? >>>> >>>> >>>> I have not seen an answer to that question (for people in the US) ? >>>> >>>> I am waiting for the PWB, which I believe I paid for, and I am planning >>>> to >>>> buy or make (have not looked into that yet) a PIC programmer, since it >>>> looks >>>> like I may get some mileage out of that anyhow. >>>> >>>> No rush, but there is no good reason to delay either at that point. >>>> >>>> Thanks >>>> >>>> Didier >>>> >>>> >>>> _______________________________________________ >>>> time-nuts mailing list -- [email protected] >>>> To unsubscribe, go to >>>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >>>> and follow the instructions there. >>>> >>>> >>>> >>>> >>>> _______________________________________________ >>>> time-nuts mailing list -- [email protected] >>>> To unsubscribe, go to >>>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >>>> and follow the instructions there. >>>> >>> >>> >>> -- >>> Steve Rooke - ZL3TUV & G8KVD >>> The only reason for time is so that everything doesn't happen at once. >>> - Einstein >>> >>> _______________________________________________ >>> time-nuts mailing list -- [email protected] >>> To unsubscribe, go to >>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >>> and follow the instructions there. >>> >> >> _______________________________________________ >> time-nuts mailing list -- [email protected] >> To unsubscribe, go to >> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >> and follow the instructions there. >> > > > -- > Steve Rooke - ZL3TUV & G8KVD > The only reason for time is so that everything doesn't happen at once. > - Einstein > > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
