All, I forgot to add this earlier today, while discussing this. When most anything is calibrated at a cal lab, lets say you have something that is supposed to be calibrated 10 MHz, then, they will generally set this at 9.9999999 MHz, or 1 millihertz below the stated value, and they do this over the resolutions decimal jump on the readout, in order to get it close enough. So, in theory, what you get could actually be 1 millihertz off. They do this on most everything, including voltage, resistance, and current calibrations. Of course, it's according to what the value is, as to what the resolution is on the last digit, and to get it within the stated tolerance. One needs to request a sheet with their measurement at the time, and if the units is powered off, it could possibly change, minutely, when powered back on. That's why most ovenized voltage references are shipped under power, to and from the cal lab, and an OCXO could possibly act the same way.
This is something one might ought to take into consideration when wanting to check something down in the low regions of measurement. Best, Will *********** REPLY SEPARATOR *********** On 7/13/2011 at 10:20 AM Will Matney wrote: >If not wanting to use an external counter, with a continuously variable >generator, the HP 3335 or 3325B would be good try out. I also think I saw a >3335A, on ebay, for around $375 to $400, in good shape, the other day. >Also, there's a difference between the 3325A and 3325B's frequency step, if >I recall, and the B version is the better one. > >Best, > >Will > >*********** REPLY SEPARATOR *********** > >On 7/13/2011 at 6:01 AM Jim Lux wrote: > >>On 7/13/11 5:55 AM, paul swed wrote: >>> hp3335 then as I sent last night >> >>or 3325... we use a lot of them at work. takes a 10MHz input, settable >>to microhertz, etc. >> >>> >>> On Wed, Jul 13, 2011 at 8:38 AM, Bill Dailey<[email protected]> >wrote: >>> >>>> Thanks for the input. I think i am asking for too much in one package >>>> (looking toward future projects). How about 1.8Mhz to 15Mhz.... To >meet the >>>> needs of the primary project (fmt). I would prefer to not have to also >use >>>> a counter. >>>> >>>> Thanks, >>>> >>>> Doc >>>> KX0O >>>> >>>> Sent from my iPad >>>> _______________________________________________ >>>> time-nuts mailing list -- [email protected] >>>> To unsubscribe, go to >>>> https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >>>> and follow the instructions there. >>>> >>> _______________________________________________ >>> time-nuts mailing list -- [email protected] >>> To unsubscribe, go to >https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >>> and follow the instructions there. >>> >> >> >>_______________________________________________ >>time-nuts mailing list -- [email protected] >>To unsubscribe, go to >https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >>and follow the instructions there. >> >>__________ Information from ESET Smart Security, version of virus >signature database 5851 (20110206) __________ >> >>The message was checked by ESET Smart Security. >> >>http://www.eset.com > > > > >_______________________________________________ >time-nuts mailing list -- [email protected] >To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >and follow the instructions there. > >__________ Information from ESET Smart Security, version of virus signature database 5851 (20110206) __________ > >The message was checked by ESET Smart Security. > >http://www.eset.com _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
