I quite like the HP 546xx series 'scopes. An "analog like" interface but good DSO facilities. My regular 'scope at home is a 54645D mixed signal. Ideal for lower speed logic/anlog circuits and 8 bit PICs. Takes up a lot less space than a 16500x logic analyser! I still keep an older analog 'scope tucked away though. I'm supriesd no-one has mentioned latency (or maybe I missed it) My last work place had a Lecroy Waverunner that was PC based and it was very annoying to use. Both signal and control response was poor. It also went off into self calibration at the most awkward moments. The 546xx has 3 lowerpower processors, each dedicated to a function and it shows. Used to have a HP 1980B and quite liked it. It was an analog 'scope with a digitiser attached. It was intened for ATE use so the single knob was not considered an issue. Robert G8RPI
________________________________ From: "gandal...@aol.com" <gandal...@aol.com> To: time-nuts@febo.com Sent: Monday, 16 April 2012, 23:29 Subject: Re: [time-nuts] Rigol scopes In a message dated 16/04/2012 22:15:50 GMT Daylight Time, lstosk...@cox.net writes: I bought one of the 50 MHz versions at Dayton last year. OK for my needs. Not mentioned here is that the difference between the 50 and 100 MHz scopes is software control of roll off on the input. I haven't done it, but procedure was available on the WEB on how to spoof the software. -------------- It's still there, and I'm surprised nobody has mentioned it earlier, it's on the eevblog forum, topic 553...... "Changing the rigol DS1052E to DS1102E using USB , the dummy guide" That forum's been running for a couple of years now and I can testify that the software "modification" works very well. I've seen it suggested that all 1052s are just 1102s that failed to meet the 100MHz spec so have been sold as the "lesser" version and that "upgraded" units will be somehow inferior to a "proper" 1102, but that's just a load of rubbish and I've performed the measurements to prove it. This is a classic example of "software defined" equipment in general where the same hardware can be sold at different prices depending on what's enabled, or crippled, in the firmware. Given the price of the 1052, especially following the reductions sometime after I bought mine and even without the bonus conversion, it's an absolute steal. Cue "the seller isn't really my wife or uncle....honest" message:-) The menu system can be a bit of a pain but it's intuitive enough to manage without the manual, and of course one has to be aware of the limitations, but I'm actually finding it far more user friendly than my Tek CRT based DSO. Perhaps one of the problems is that the Rigols really do offer so much for so little, and in a relatively small box, that it's sometimes difficult to take them as seriously as they deserve. I still think of the Tek, and an older HP1740 that's tucked away somewhere, as my "real" scopes but it's interesting that the 1052/1102 is always now the first one I turn to as my general purpose bench unit. Interesting too to consider that it's had no problem displaying the 1PPS pulse from several 5680A Rubidium units whilst half the list was still querying whether or not such pulses even existed:-) There was an earlier post mentioned the "spontaneous" splitting of knobs and I have to agree this can be a problem. Having had three that split, without provocation or a by your leave, I was eventually sent some replacements only to find it was impossible to force them on to the shafts without pushing the attached PCB out of the back of the scope and into never never land. On that basis I decided it probably wasn't so much another case of poor quality Chinese plastics as just another case of poor Chinese not quite getting the size right! So now I have some substitute knobs that do fit, don't quite match but what the heck, and a scope that still works remarkably well. I can live with that:-) Nigel GM8PZR _______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. _______________________________________________ time-nuts mailing list -- time-nuts@febo.com To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.