To expand on the replies by Bob and Magnus... Many years ago after pForth was discovered inside the entire hp 585xx and Z38xx series "SmartClock" GPSDO, Magnus and I worked on the mystery of how the 58503A GPSDO worked so well. HP appears to use a 64-entry circular buffer to record hourly EFC history. Given 64 hours (2.7 days) of data, a GPSDO can make a reasonable prediction of GPS reception or OCXO frequency stability (via ADEV-like statistics) and frequency drift (via linear or quadratic LSQ fits).
Why 64 hours? Well, C programmers working with circular buffers like powers of 2. And from personal experience working with GPSDO I know that high sampling rates are mostly noise and not useful. So hourly EFC data makes sense to me. Also from experience I know that less than one day of EFC data can be misleading. Similarly more than a week of stale past data can also be irrelevant to a prediction of 1 day into the future. So for all these reasons, 64 hours seems an adequate choice. Note HP and other high-end GPSDO provide both a FFOM (frequency figure of merit) and TFOM (time FOM) value via the SCPI interface. There is lots more info on all these subjects scattered in the time-nuts archives. Here's an example 58503 dump (log1348.txt): p4th D > pr_efc efc = 280607.843750 p4th D > pll_rep start ptr = 7 stop_ptr = 6 max loop time = -1412584448 ffom = 0 tfom = 1.0e-06 secs p4th D > efc_rep 65.698517 282457.3 3 66.698517 282468.8 3 67.698517 282473.8 3 68.698517 282485.2 3 69.698517 282490.1 3 70.698517 282496.9 3 7.698519 280841.3 3 8.698519 280943.2 3 9.698519 281063.8 3 10.698519 281126.8 3 11.698519 281185.4 3 12.698519 281259.0 3 13.698519 281316.7 3 14.698519 281353.4 3 15.698519 281413.1 3 16.698519 281464.9 3 17.698519 281511.9 3 18.698519 281567.6 3 19.698519 281622.8 3 20.698519 281634.8 3 21.698519 281671.7 3 22.698519 281705.8 3 23.698519 281736.4 3 24.698519 281768.2 3 25.698519 281813.6 3 26.698519 281847.9 3 27.698519 281872.4 3 28.698519 281899.0 3 29.698519 281919.0 3 30.698519 281950.0 3 31.698519 281974.3 3 32.698517 282001.1 3 33.698517 282043.5 3 34.698517 282054.2 3 35.698517 282056.2 3 36.698517 282060.2 3 37.698517 282081.5 3 38.698517 282092.2 3 39.698517 282093.2 3 40.698517 282094.1 3 41.698517 282100.7 3 42.698517 282127.8 3 43.698517 282126.1 3 44.698517 282143.3 3 45.698517 282150.0 3 46.698517 282162.9 3 47.698517 282188.4 3 48.698517 282213.4 3 49.698517 282244.7 3 50.698517 282255.4 3 51.698517 282260.3 3 52.698517 282280.5 3 53.698517 282286.6 3 54.698517 282307.0 3 55.698517 282319.3 3 56.698517 282336.2 3 57.698517 282350.4 3 58.698517 282367.3 3 59.698517 282367.2 3 60.698517 282395.8 3 61.698517 282411.4 3 62.698517 282430.3 3 63.698517 282441.6 3 64.698517 282450.1 3 a= 2.793488e+05 b= -2.535462e+00 c= 7.822419e+02 p4th D > /tvb ----- Original Message ----- From: "Magnus Danielson" <[email protected]> To: <[email protected]> Cc: <[email protected]> Sent: Thursday, October 06, 2016 3:40 PM Subject: Re: [time-nuts] Measure GPSDO stability with minimum resources? Hi, On 10/06/2016 08:38 PM, Bob Camp wrote: > Hi > > One very simple experiment: > > Take a HP that has been off power for a year or so. Fire it up and watch it’s > predictions > of holdover accuracy. Many of them will go through a “zero” time estimate at > one or > two days. At three or four days they are struggling to hit spec (10us). The > reason is > pretty simple. The OCXO warmed up and went through an inflection (reversal in > direction). > They estimated across the inflection, got zero and passed that on …. Indeed. The Z3801A does a least-square fit and then tries to maintain that. If done at the wrong time it will be wildly off. I don't remember the details, but I think I recall that you can trigger the re-calibration routine which is what you want to do to drive it in the right direction. Least-square fitting isn't all that magic and doesn't really require lots of memory, if you do it properly. You just need the oscillator to heat up and settle before you attempt to do anything involving long time-constants. Usually it's not the core algorithms, but the heuristics that needs to work well. Cheers, Magnus _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
