Hi, I programmed the mote(supposed to be the base station that is connected to mib520) with XMeshBase_2420_hp under C:\Program Files\Crossbow\MoteView\xmesh\micaz\XMeshBase. But still I am not able to display sensor data in pc.
Regards, Dhivya. On Wed, Apr 9, 2008 at 1:48 PM, Marco Antonio Lopez Trinidad < [EMAIL PROTECTED]> wrote: > What is the program you use? > > 1. TinyOS SerialForwarder uses the next port you use to connect the > programmer. > 2. MoteWorks applications suite recognises automatically the right ports > to > program (com_i) and inject or read packets (com_i+1). > > I hope it helps, > --marco. > > > Hi Anil, > > I am getting 2 ports(com5 and com6) while connecting MIB520 to pc. > > In step 2, I am programming my mote that is connected to Mib520. So > while > > Programming I have to give lower port(com5). In step 5, I am getting > data > > from sensors and have to display it in PC.So for communication part I > have > > to use higher port(com6). This is wht I did earlier. > > I also tried your idea.But I am getting following error. > > "Can not connect to Mote correctly. Please check your Mote." > > > > Regards, > > Dhivya > > > > > > On Wed, Apr 9, 2008 at 12:47 PM, Anil Karamchandani <[EMAIL PROTECTED]> > > wrote: > > > > > Hi Dhivya, > > > > > > the port number should be the port through which your gateway device > is > > > connected to the PC. Usually the port number in step 2 and step 5 is > the > > > same. check for the port which is communicating with the sensor and > the PC > > > and give that port number .. > > > > > > hope this helps > > > > > > anil > > > > > > On Wed, Apr 9, 2008 at 12:34 PM, Dhivya G <[EMAIL PROTECTED]> wrote: > > > > > > > > > > > Hai, > > > > I am using crossbow Professional kit consisting of Micaz > motes,MIB520 > > > > programming board and MTS400 sensor board. I want to know whether I > have > > to > > > > program Micaz mote(connected to mib520) to collect data from sensor > using > > > > Moteview.If so how I have to program Micaz mote. > > > > I Connected one micaz mote to mib520 programming board and > > > > programmed it using moteconfig as follows: > > > > 1) In Moteview I clicked Tools->Program Motes > > > > 2)In MoteConfig window I clicked Settings->Interface Board. In > Interface > > > > board settings window I selected MIB520 and changed com port to 5 > (lower > > > > port)and clicked Apply. > > > > 3)Then I clicked select button under "select file to be uploaded". I > > > > selected XMeshBase_2420_hp under C:\Program > > > > Files\Crossbow\MoteView\xmesh\micaz\XMeshBase > > > > 4)Then I clicked Program button. > > > > 5)After finishing program I clicked File->Connect to WSN. In that > new > > > > window I selected MIB520 board and com6(higher port) and XMTS400 > board. > > > > 6)After completing all these steps sensor data is not displaying in > PC. > > > > > > > > If my steps are wrong means please correct me. > > > > -- > > > > G.Dhivya > > > > _______________________________________________ > > > > Tinyos-help mailing list > > > > [email protected] > > > > > https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help > > > > > > > > > > > > > > > > -- > > > Regards > > > > > > Anil Karamchandani > > > > > > > > > > -- > > G.Dhivya > > > > > > -- G.Dhivya
_______________________________________________ Tinyos-help mailing list [email protected] https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
