I just tested it. Same here. Not working. Thanks for your help anyway.  Any
other ideas?

Cheers,
Bai

On Wed, Dec 17, 2008 at 12:59 PM, Hui Kang <[email protected]> wrote:

> Add this line to your makefile and remove those macro.
> CFLAGS=-DCC2420_DEF_RFPOWER=3
>
>
> - Hui
>
> BAI LI wrote:
>
>> I read the cc2420 datasheet and modified it but unluckily it still didn't
>> work. I modified the following code repectivcely.
>>  #ifndef CC2420_DEF_RFPOWER
>> #define CC2420_DEF_RFPOWER          0x1F    // changed the 0x1F to 3 or 1,
>> didn't work.
>> #endif
>>  cheers,
>> Bai
>> ================================
>>  On Wed, Dec 17, 2008 at 8:30 AM, Nitin Sharma <[email protected]<mailto:
>> [email protected]>> wrote:
>>
>>    Hi,
>>
>>    Could you try setting it to 3 or a little higher instead and see?
>>
>>    PA_Level 3 Output Power -25 , TXCTRL register 0xA0E3
>>
>>    The output power is programmable in 8 steps from approximately –24
>>    to 0 dBm.
>>
>>    Page: 9 , 52 from CC2420 Data Sheet.
>>
>>    Thanks,
>>
>>    On Tue, Dec 16, 2008 at 2:47 PM, BAI LI <[email protected]
>>    <mailto:[email protected]>> wrote:
>>
>>        Yes, i modified the code. the default value of REPOAWER is 31
>>        at the maximum in Tinyos1.15. Then I changed it to 1. I
>>        believe nothing changed. The node still can communicate with
>>        other nodes at least 15 meters. It is not that good. I will
>>        try to use setRFPower. Is this the right value I should change
>>        in order to decrease the transimission distance. I am
>>        confused. Anyone who has experience, please help me. THanks in
>>        advanced.
>>
>>        On Tue, Dec 16, 2008 at 11:16 AM, Razvan Musaloiu-E.
>>        <[email protected] <mailto:[email protected]>> wrote:
>>
>>            Hi!
>>
>>
>>            On Mon, 15 Dec 2008, BAI LI wrote:
>>
>>                Hi All,
>>                Anyone can tell me where to modify the power level in
>>                tinyos 1.x and tinyos
>>                2.x?
>>
>>
>>            In tinyos-2.x you can set the global radio power of CC2420
>>            by defining the CC2420_DEF_RFPOWER to a different value or
>>            you can change it dynamically on a per-packet basis using
>>            the setPower command from the CC2420Packet interface.
>>
>>            --
>>            Razvan ME
>>
>>
>>
>>        _______________________________________________
>>        Tinyos-help mailing list
>>        [email protected]
>>        <mailto:[email protected]>
>>
>> https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
>>
>>
>>
>>
>>    --    Nitin Sharma
>>
>>
>> ------------------------------------------------------------------------
>>
>> _______________________________________________
>> Tinyos-help mailing list
>> [email protected]
>> https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
>>
>
>
>
_______________________________________________
Tinyos-help mailing list
[email protected]
https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help

Reply via email to