Yes I have connected the mib520 to wmware! And I checked that the device file /dev/ttyUSB0 exists! But the message is the same, that: "Probably the AVR MCU is not in the RESET state." Why is that?
Kokai 2009/3/12 Janos Sallai <[email protected]> > Have you connected the mib520 to vmware? If yes, please make sure that > the device file /dev/ttyUSB0 exists. > > Janos > > On Thu, Mar 12, 2009 at 10:01 AM, Péter Kókai <[email protected]> > wrote: > > Hmm..I thought I need to write the comX port to the command yet. > > I saw in the device manager under Windows that the ports where the device > > was jointed are com10 and com11. > > So it seems I was wrong! > > Cause I tried what you wrote! And it was working, but I got another > message: > > > > xubun...@xubuntos-tinyos:~/Desktop/mikay$ uisp -dprog=mib510 > > -dserial=/dev/ttyUSB0 --wr_fuse_h=0xd9 -dpart=ATmega128 --w > > Firmware Version: 1.8 > > Probably the AVR MCU is not in the RESET state. > > Check it out and run me again. > > > > Why did I get this message? > > > > Thanks! > > Peter Kokai > > > > > > > > > > 2009/3/12 Janos Sallai <[email protected]> > >> > >> Peter, > >> > >> I guess the port you specified is wrong: > >> > xubun...@xubuntos-tinyos:~/Desktop/mikay$ uisp -dprog=mib510 > >> > -dserial=/dev/tty9 --wr_fuse_h=0xd9 -dpart=ATmega128 --w > >> > >> The mib520 shows up as two serial ports under linux, typically > >> /dev/ttyUSB0 and /dev/ttyUSB1. You need to specify the lower one if > >> you want to program the mote and the higher one to communicate with > >> it. > >> > >> Janos > >> > >> > >> On Thu, Mar 12, 2009 at 8:07 AM, Péter Kókai <[email protected]> > wrote: > >> > Thx Kaisen the help! > >> > > >> > But I have a new problem after this! A try this command in the folder > >> > containing the hex file, and I don't get any error message, so this is > a > >> > good new! =) > >> > But after this I get this message: Programmer is not responding! > >> > > >> > xubun...@xubuntos-tinyos:~/Desktop/mikay$ uisp -dprog=mib510 > >> > -dserial=/dev/tty9 --wr_fuse_h=0xd9 -dpart=ATmega128 --w > >> > Programmer is not responding. > >> > > >> > I thought that maybe the file format is not good, so I convert the hex > >> > file > >> > to .srec file as you wrote! > >> > But the same result! > >> > I tried to change the port: I use the com10 and com11: I tried both of > >> > them, > >> > but the same result I got! > >> > Can somebody help me to find the solution? > >> > I'm starter in these things: tinyos, micaz and mib520! > >> > > >> > Thanks > >> > Peter Kokai > >> > > >> > > >> > > >> > > >> > 2009/3/11 Kaisen Lin <[email protected]> > >> >> > >> >> You need the uisp program, and the command is: > >> >> > >> >> uisp -dprog=mib510 -dserial=/dev/ttyUSB0 --wr_fuse_h=0xd9 > >> >> -dpart=ATmega128 > >> >> --w > >> >> r_fuse_e=ff --erase --upload if=main.srec --verify > >> >> > >> >> Make sure you to check what your USB port is. There are two (one for > >> >> programming, one for communication, use the first one). The file in > >> >> this > >> >> case is main.srec. Your hex file might work, but I'm not 100% sure. > You > >> >> can > >> >> try it. If not, just convert it to an srec. > >> >> > >> >> Kaisen > >> >> > >> >> ----- "Péter Kókai" <[email protected]> wrote: > >> >> > >> >> > Hi all! > >> >> > > >> >> > I have a micaz mote, and a MIB520 programming board! > >> >> > And my problem is, that I have a program what was write with > >> >> > AVRStudio > >> >> > 4 in Assembly, cause I have to use this language. It generated a > .hex > >> >> > file! And I should upload this file to the mote! > >> >> > I thought that I can do this with tinyOS, but I couldn't! I tried > to > >> >> > figure out a solution but I wasn't successful yet! > >> >> > Is there any chance to do this with TinyOs? To upload a .hex file > to > >> >> > the mote? > >> >> > > >> >> > Thanks & Regard > >> >> > Peter Kokai > >> >> > _______________________________________________ > >> >> > Tinyos-help mailing list > >> >> > [email protected] > >> >> > > >> >> > > https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help > >> > > >> > > >> > > >> > -- > >> > Üdv: Kókai > >> > ___ > >> > Have a Nice Night!!! > >> > > >> > _______________________________________________ > >> > Tinyos-help mailing list > >> > [email protected] > >> > > https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help > >> > > > > > > > > > -- > > Üdv: Kókai > > ___ > > Have a Nice Night!!! > > > -- Üdv: Kókai ___ Have a Nice Night!!!
_______________________________________________ Tinyos-help mailing list [email protected] https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
