You're right!! I checked more times the connection, and now I try to push a litle bit while I start it! And yes, it was useful! But now I have another message: xubun...@xubuntos-tinyos:~/Desktop/mikay$ uisp -dprog=mib510 -dserial=/dev/ttyUSB0 --wr_fuse_h=0xd9 -dpart=ATmega128 --w Firmware Version: 1.8 Atmel AVR ATmega128 is found.
Fuse High Byte set to 0xd9 Invalid parameter: --w It wrote that there is something wrong with the last part of the command! I just started to use tinyos last week, so I don't know that it is a wrong parameter, or something else is wrong! Can you help me in this? And thank you very much the help till now! Kokai! 2009/3/12 Janos Sallai <[email protected]> > > Firmware Version: 1.8 > This means that the MIB520 is found and that it is working. > > > Probably the AVR MCU is not in the RESET state. > This is the error you get when the mote is not connected to the > programming board. > > Can you double check the connection between the mote and the programming > board? > > Janos > > > > On Thu, Mar 12, 2009 at 10:28 AM, Péter Kókai <[email protected]> > wrote: > > Yes I have connected the mib520 to wmware! > > And I checked that the device file /dev/ttyUSB0 exists! > > But the message is the same, that: "Probably the AVR MCU is not in the > RESET > > state." > > Why is that? > > > > Kokai > > > > > > 2009/3/12 Janos Sallai <[email protected]> > >> > >> Have you connected the mib520 to vmware? If yes, please make sure that > >> the device file /dev/ttyUSB0 exists. > >> > >> Janos > >> > >> On Thu, Mar 12, 2009 at 10:01 AM, Péter Kókai <[email protected]> > >> wrote: > >> > Hmm..I thought I need to write the comX port to the command yet. > >> > I saw in the device manager under Windows that the ports where the > >> > device > >> > was jointed are com10 and com11. > >> > So it seems I was wrong! > >> > Cause I tried what you wrote! And it was working, but I got another > >> > message: > >> > > >> > xubun...@xubuntos-tinyos:~/Desktop/mikay$ uisp -dprog=mib510 > >> > -dserial=/dev/ttyUSB0 --wr_fuse_h=0xd9 -dpart=ATmega128 --w > >> > Firmware Version: 1.8 > >> > Probably the AVR MCU is not in the RESET state. > >> > Check it out and run me again. > >> > > >> > Why did I get this message? > >> > > >> > Thanks! > >> > Peter Kokai > >> > > >> > > >> > > >> > > >> > 2009/3/12 Janos Sallai <[email protected]> > >> >> > >> >> Peter, > >> >> > >> >> I guess the port you specified is wrong: > >> >> > xubun...@xubuntos-tinyos:~/Desktop/mikay$ uisp -dprog=mib510 > >> >> > -dserial=/dev/tty9 --wr_fuse_h=0xd9 -dpart=ATmega128 --w > >> >> > >> >> The mib520 shows up as two serial ports under linux, typically > >> >> /dev/ttyUSB0 and /dev/ttyUSB1. You need to specify the lower one if > >> >> you want to program the mote and the higher one to communicate with > >> >> it. > >> >> > >> >> Janos > >> >> > >> >> > >> >> On Thu, Mar 12, 2009 at 8:07 AM, Péter Kókai <[email protected]> > >> >> wrote: > >> >> > Thx Kaisen the help! > >> >> > > >> >> > But I have a new problem after this! A try this command in the > folder > >> >> > containing the hex file, and I don't get any error message, so this > >> >> > is a > >> >> > good new! =) > >> >> > But after this I get this message: Programmer is not responding! > >> >> > > >> >> > xubun...@xubuntos-tinyos:~/Desktop/mikay$ uisp -dprog=mib510 > >> >> > -dserial=/dev/tty9 --wr_fuse_h=0xd9 -dpart=ATmega128 --w > >> >> > Programmer is not responding. > >> >> > > >> >> > I thought that maybe the file format is not good, so I convert the > >> >> > hex > >> >> > file > >> >> > to .srec file as you wrote! > >> >> > But the same result! > >> >> > I tried to change the port: I use the com10 and com11: I tried both > >> >> > of > >> >> > them, > >> >> > but the same result I got! > >> >> > Can somebody help me to find the solution? > >> >> > I'm starter in these things: tinyos, micaz and mib520! > >> >> > > >> >> > Thanks > >> >> > Peter Kokai > >> >> > > >> >> > > >> >> > > >> >> > > >> >> > 2009/3/11 Kaisen Lin <[email protected]> > >> >> >> > >> >> >> You need the uisp program, and the command is: > >> >> >> > >> >> >> uisp -dprog=mib510 -dserial=/dev/ttyUSB0 --wr_fuse_h=0xd9 > >> >> >> -dpart=ATmega128 > >> >> >> --w > >> >> >> r_fuse_e=ff --erase --upload if=main.srec --verify > >> >> >> > >> >> >> Make sure you to check what your USB port is. There are two (one > for > >> >> >> programming, one for communication, use the first one). The file > in > >> >> >> this > >> >> >> case is main.srec. Your hex file might work, but I'm not 100% > sure. > >> >> >> You > >> >> >> can > >> >> >> try it. If not, just convert it to an srec. > >> >> >> > >> >> >> Kaisen > >> >> >> > >> >> >> ----- "Péter Kókai" <[email protected]> wrote: > >> >> >> > >> >> >> > Hi all! > >> >> >> > > >> >> >> > I have a micaz mote, and a MIB520 programming board! > >> >> >> > And my problem is, that I have a program what was write with > >> >> >> > AVRStudio > >> >> >> > 4 in Assembly, cause I have to use this language. It generated a > >> >> >> > .hex > >> >> >> > file! And I should upload this file to the mote! > >> >> >> > I thought that I can do this with tinyOS, but I couldn't! I > tried > >> >> >> > to > >> >> >> > figure out a solution but I wasn't successful yet! > >> >> >> > Is there any chance to do this with TinyOs? To upload a .hex > file > >> >> >> > to > >> >> >> > the mote? > >> >> >> > > >> >> >> > Thanks & Regard > >> >> >> > Peter Kokai > >> >> >> > _______________________________________________ > >> >> >> > Tinyos-help mailing list > >> >> >> > [email protected] > >> >> >> > > >> >> >> > > >> >> >> > > https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help > >> >> > > >> >> > > >> >> > > >> >> > -- > >> >> > Üdv: Kókai > >> >> > ___ > >> >> > Have a Nice Night!!! > >> >> > > >> >> > _______________________________________________ > >> >> > Tinyos-help mailing list > >> >> > [email protected] > >> >> > > >> >> > > https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help > >> >> > > >> > > >> > > >> > > >> > -- > >> > Üdv: Kókai > >> > ___ > >> > Have a Nice Night!!! > >> > > > > > > > > > -- > > Üdv: Kókai > > ___ > > Have a Nice Night!!! > > > > _______________________________________________ > > Tinyos-help mailing list > > [email protected] > > https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help > > > -- Üdv: Kókai ___ Have a Nice Night!!!
_______________________________________________ Tinyos-help mailing list [email protected] https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
