Hi, I am using Xubuntos, and it doesnt say any thing when i connect the board. when i check motes using $motelist, it says no devices found. I checked google and found i should install FT2232C driver(VCP). but i am not able it install it as weel. Please can you suggest how to program micaz in xubuntos.
regards, Praveen Razvan Musaloiu-E.-2 wrote: > > Hi! > > On Thu, 27 Aug 2009, praveen khethavath wrote: > >> >> Hi, >> >> This is Praveen and i am doing PhD in Oklahoma state university. >> I was not able to install the FT2232C driver on XUBUNTOS machine. >> I am not able tp program Micaz using MIB520. >> >> when i try to make micaz install i see following error. >> The device is not recognized. >> >> make micaz install mib510,/dev/ttyS0 > > Try to do a dmesg after you plug the board. The messages should indicate > which /dev/ttyUSBX (never /dev/ttySX) device it gets. The MIB520 will get > two: the first one is used to reprogram the mote while the second is used > to talk to the mote's serial port. > > All the best! > Razvan ME > >> mkdir -p build/micaz >> compiling BlinkAppC to a micaz binary >> ncc -o build/micaz/main.exe -Os -fnesc-separator=__ -Wall -Wshadow >> -Wnesc-all -target=micaz -fnesc-cfile=build/micaz/app.c -board=micasb >> -DDEFINED_TOS_AM_GROUP=0x22 --param max-inline-insns-single=100000 >> -DIDENT_APPNAME=\"BlinkAppC\" -DIDENT_USERNAME=\"praveen\" >> -DIDENT_HOSTNAME=\"praveen-laptop\" -DIDENT_USERHASH=0x0fa84db1L >> -DIDENT_TIMESTAMP=0x4a971fa5L -DIDENT_UIDHASH=0xd90a9f1eL >> -fnesc-dump=wiring >> -fnesc-dump='interfaces(!abstract())' >> -fnesc-dump='referenced(interfacedefs, >> components)' -fnesc-dumpfile=build/micaz/wiring-check.xml BlinkAppC.nc >> -lm >> compiled BlinkAppC to build/micaz/main.exe >> 2052 bytes in ROM >> 51 bytes in RAM >> avr-objcopy --output-target=srec build/micaz/main.exe >> build/micaz/main.srec >> avr-objcopy --output-target=ihex build/micaz/main.exe >> build/micaz/main.ihex >> writing TOS image >> cp build/micaz/main.srec build/micaz/main.srec.out >> installing micaz binary using mib510 >> uisp -dprog=mib510 -dserial=/dev/ttyS0 --wr_fuse_h=0xd9 -dpart=ATmega128 >> --wr_fuse_e=ff --erase --upload if=build/micaz/main.srec.out --verify >> Programmer is not responding. >> make: *** [program] Error 2 >> >> Can you suggest how can i use mib520 in XUBUNTOS >> >> Thanks. >> >> -- >> View this message in context: >> http://www.nabble.com/Mib520-FT2232C-driver-installation-tp25182815p25182815.html >> Sent from the TinyOS - Help mailing list archive at Nabble.com. >> >> _______________________________________________ >> Tinyos-help mailing list >> [email protected] >> https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help >> > _______________________________________________ > Tinyos-help mailing list > [email protected] > https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help > > -- View this message in context: http://www.nabble.com/Mib520-FT2232C-driver-installation-tp25182815p25192500.html Sent from the TinyOS - Help mailing list archive at Nabble.com. _______________________________________________ Tinyos-help mailing list [email protected] https://www.millennium.berkeley.edu/cgi-bin/mailman/listinfo/tinyos-help
