Fully resetting the controller is a too big hammer, and the musb_core will
then afterwards fail to communicate with any endpoints other then 0 as
too much state was cleared.
Instead report vbus low for 200ms which will effectively end the current
session without needing to do a full reset.
This fixes usb mass-storage devices no longer working after a "usb reset"
Signed-off-by: Hans de Goede <hdego...@redhat.com>
---
drivers/usb/musb-new/sunxi.c | 52 ++++++++++++++++++++++++++------------------
1 file changed, 31 insertions(+), 21 deletions(-)
diff --git a/drivers/usb/musb-new/sunxi.c b/drivers/usb/musb-new/sunxi.c
index e8a3a23..42c6725 100644
--- a/drivers/usb/musb-new/sunxi.c
+++ b/drivers/usb/musb-new/sunxi.c
@@ -157,6 +157,17 @@ static void USBC_ForceIdToHigh(__iomem void *base)
musb_writel(base, USBC_REG_o_ISCR, reg_val);
}
+static void USBC_ForceVbusValidToLow(__iomem void *base)
+{
+ u32 reg_val;
+
+ reg_val = musb_readl(base, USBC_REG_o_ISCR);
+ reg_val &= ~(0x03 << USBC_BP_ISCR_FORCE_VBUS_VALID);
+ reg_val |= (0x02 << USBC_BP_ISCR_FORCE_VBUS_VALID);
+ reg_val = USBC_WakeUp_ClearChangeDetect(reg_val);
+ musb_writel(base, USBC_REG_o_ISCR, reg_val);
+}
+
static void USBC_ForceVbusValidToHigh(__iomem void *base)
{
u32 reg_val;
@@ -205,42 +216,41 @@ static irqreturn_t sunxi_musb_interrupt(int irq, void
*__hci)
return retval;
}
+/* musb_core does not call enable / disable in a balanced manner <sigh> */
+static bool enabled = false;
+
static void sunxi_musb_enable(struct musb *musb)
{
pr_debug("%s():\n", __func__);
+ if (enabled)
+ return;
+
/* select PIO mode */
musb_writeb(musb->mregs, USBC_REG_o_VEND0, 0);
- if (is_host_enabled(musb)) {
- /* port power on */
- sunxi_usb_phy_power_on(0);
- }
+ if (is_host_enabled(musb))
+ sunxi_usb_phy_power_on(0); /* port power on */
+
+ USBC_ForceVbusValidToHigh(musb->mregs);
+
+ enabled = true;
}
static void sunxi_musb_disable(struct musb *musb)
{
- struct sunxi_ccm_reg *ccm = (struct sunxi_ccm_reg *)SUNXI_CCM_BASE;
-
pr_debug("%s():\n", __func__);
- /* Put the controller back in a pristane state for "usb reset" */
- if (musb->is_active) {
- sunxi_usb_phy_exit(0);
-#ifdef CONFIG_SUNXI_GEN_SUN6I
- clrbits_le32(&ccm->ahb_reset0_cfg, 1 << AHB_GATE_OFFSET_USB0);
-#endif
- clrbits_le32(&ccm->ahb_gate0, 1 << AHB_GATE_OFFSET_USB0);
+ if (!enabled)
+ return;
- mdelay(10);
+ if (is_host_enabled(musb))
+ sunxi_usb_phy_power_off(0); /* port power off */
- setbits_le32(&ccm->ahb_gate0, 1 << AHB_GATE_OFFSET_USB0);
-#ifdef CONFIG_SUNXI_GEN_SUN6I
- setbits_le32(&ccm->ahb_reset0_cfg, 1 << AHB_GATE_OFFSET_USB0);
-#endif
- sunxi_usb_phy_init(0);
- musb->is_active = 0;
- }
+ USBC_ForceVbusValidToLow(musb->mregs);
+ mdelay(200); /* Wait for the current session to timeout */
+
+ enabled = false;
}
static int sunxi_musb_init(struct musb *musb)
--
2.4.3
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
