Instead of using multiple macros, a data structure is used to pass
board-specific parameters to MMDC DDR driver.
Signed-off-by: York Sun <york....@nxp.com>
CC: Shengzhou Liu <shengzhou....@nxp.com>
---
board/freescale/ls1012afrdm/ls1012afrdm.c | 18 ++++++++++++++-
board/freescale/ls1012aqds/ls1012aqds.c | 18 ++++++++++++++-
board/freescale/ls1012ardb/ls1012ardb.c | 18 ++++++++++++++-
drivers/ddr/fsl/fsl_mmdc.c | 38 +++++++++++++++----------------
include/configs/ls1012afrdm.h | 16 -------------
include/configs/ls1012aqds.h | 16 -------------
include/configs/ls1012ardb.h | 15 ------------
include/fsl_mmdc.h | 21 +++++++++++++----
8 files changed, 87 insertions(+), 73 deletions(-)
diff --git a/board/freescale/ls1012afrdm/ls1012afrdm.c
b/board/freescale/ls1012afrdm/ls1012afrdm.c
index d644e94..b03bdb8 100644
--- a/board/freescale/ls1012afrdm/ls1012afrdm.c
+++ b/board/freescale/ls1012afrdm/ls1012afrdm.c
@@ -26,7 +26,23 @@ int checkboard(void)
int dram_init(void)
{
- mmdc_init();
+ static const struct fsl_mmdc_info mparam = {
+ 0x04180000, /* mdctl */
+ 0x00030035, /* mdpdc */
+ 0x12554000, /* mdotc */
+ 0xbabf7954, /* mdcfg0 */
+ 0xdb328f64, /* mdcfg1 */
+ 0x01ff00db, /* mdcfg2 */
+ 0x00001680, /* mdmisc */
+ 0x0f3c8000, /* mdref */
+ 0x00002000, /* mdrwd */
+ 0x00bf1023, /* mdor */
+ 0x0000003f, /* mdasp */
+ 0x0000022a, /* mpodtctrl */
+ 0xa1390003, /* mpzqhwctrl */
+ };
+
+ mmdc_init(&mparam);
gd->ram_size = CONFIG_SYS_SDRAM_SIZE;
diff --git a/board/freescale/ls1012aqds/ls1012aqds.c
b/board/freescale/ls1012aqds/ls1012aqds.c
index 188b6bc..94440b3 100644
--- a/board/freescale/ls1012aqds/ls1012aqds.c
+++ b/board/freescale/ls1012aqds/ls1012aqds.c
@@ -54,7 +54,23 @@ int checkboard(void)
int dram_init(void)
{
- mmdc_init();
+ static const struct fsl_mmdc_info mparam = {
+ 0x05180000, /* mdctl */
+ 0x00030035, /* mdpdc */
+ 0x12554000, /* mdotc */
+ 0xbabf7954, /* mdcfg0 */
+ 0xdb328f64, /* mdcfg1 */
+ 0x01ff00db, /* mdcfg2 */
+ 0x00001680, /* mdmisc */
+ 0x0f3c8000, /* mdref */
+ 0x00002000, /* mdrwd */
+ 0x00bf1023, /* mdor */
+ 0x0000003f, /* mdasp */
+ 0x0000022a, /* mpodtctrl */
+ 0xa1390003, /* mpzqhwctrl */
+ };
+
+ mmdc_init(&mparam);
gd->ram_size = CONFIG_SYS_SDRAM_SIZE;
diff --git a/board/freescale/ls1012ardb/ls1012ardb.c
b/board/freescale/ls1012ardb/ls1012ardb.c
index 50f9187..778434d 100644
--- a/board/freescale/ls1012ardb/ls1012ardb.c
+++ b/board/freescale/ls1012ardb/ls1012ardb.c
@@ -58,7 +58,23 @@ int checkboard(void)
int dram_init(void)
{
- mmdc_init();
+ static const struct fsl_mmdc_info mparam = {
+ 0x05180000, /* mdctl */
+ 0x00030035, /* mdpdc */
+ 0x12554000, /* mdotc */
+ 0xbabf7954, /* mdcfg0 */
+ 0xdb328f64, /* mdcfg1 */
+ 0x01ff00db, /* mdcfg2 */
+ 0x00001680, /* mdmisc */
+ 0x0f3c8000, /* mdref */
+ 0x00002000, /* mdrwd */
+ 0x00bf1023, /* mdor */
+ 0x0000003f, /* mdasp */
+ 0x0000022a, /* mpodtctrl */
+ 0xa1390003, /* mpzqhwctrl */
+ };
+
+ mmdc_init(&mparam);
gd->ram_size = CONFIG_SYS_SDRAM_SIZE;
diff --git a/drivers/ddr/fsl/fsl_mmdc.c b/drivers/ddr/fsl/fsl_mmdc.c
index 1e35967..52eec0f 100644
--- a/drivers/ddr/fsl/fsl_mmdc.c
+++ b/drivers/ddr/fsl/fsl_mmdc.c
@@ -26,7 +26,7 @@ static void set_wait_for_bits_clear(void *ptr, u32 value, u32
bits)
printf("Error: %p wait for clear timeout.\n", ptr);
}
-void mmdc_init(void)
+void mmdc_init(const struct fsl_mmdc_info *priv)
{
struct mmdc_regs *mmdc = (struct mmdc_regs *)CONFIG_SYS_FSL_DDR_ADDR;
unsigned int tmp;
@@ -35,26 +35,26 @@ void mmdc_init(void)
out_be32(&mmdc->mdscr, MDSCR_ENABLE_CON_REQ);
/* 2. configure the desired timing parameters */
- out_be32(&mmdc->mdotc, CONFIG_MMDC_MDOTC);
- out_be32(&mmdc->mdcfg0, CONFIG_MMDC_MDCFG0);
- out_be32(&mmdc->mdcfg1, CONFIG_MMDC_MDCFG1);
- out_be32(&mmdc->mdcfg2, CONFIG_MMDC_MDCFG2);
+ out_be32(&mmdc->mdotc, priv->mdotc);
+ out_be32(&mmdc->mdcfg0, priv->mdcfg0);
+ out_be32(&mmdc->mdcfg1, priv->mdcfg1);
+ out_be32(&mmdc->mdcfg2, priv->mdcfg2);
/* 3. configure DDR type and other miscellaneous parameters */
- out_be32(&mmdc->mdmisc, CONFIG_MMDC_MDMISC);
+ out_be32(&mmdc->mdmisc, priv->mdmisc);
out_be32(&mmdc->mpmur0, MMDC_MPMUR0_FRC_MSR);
- out_be32(&mmdc->mdrwd, CONFIG_MMDC_MDRWD);
- out_be32(&mmdc->mpodtctrl, CONFIG_MMDC_MPODTCTRL);
+ out_be32(&mmdc->mdrwd, priv->mdrwd);
+ out_be32(&mmdc->mpodtctrl, priv->mpodtctrl);
/* 4. configure the required delay while leaving reset */
- out_be32(&mmdc->mdor, CONFIG_MMDC_MDOR);
+ out_be32(&mmdc->mdor, priv->mdor);
/* 5. configure DDR physical parameters */
/* set row/column address width, burst length, data bus width */
- tmp = CONFIG_MMDC_MDCTL & ~(MDCTL_SDE0 | MDCTL_SDE1);
+ tmp = priv->mdctl & ~(MDCTL_SDE0 | MDCTL_SDE1);
out_be32(&mmdc->mdctl, tmp);
/* configure address space partition */
- out_be32(&mmdc->mdasp, CONFIG_MMDC_MDASP);
+ out_be32(&mmdc->mdasp, priv->mdasp);
/* 6. perform a ZQ calibration - not needed here, doing in #8b */
@@ -84,7 +84,7 @@ void mmdc_init(void)
out_be32(&mmdc->mdscr, CMD_ADDR_MSB_MR_OP(0x4) | MDSCR_ENABLE_CON_REQ |
CMD_ZQ_CALIBRATION | CMD_BANK_ADDR_0);
- set_wait_for_bits_clear(&mmdc->mpzqhwctrl, CONFIG_MMDC_MPZQHWCTRL,
+ set_wait_for_bits_clear(&mmdc->mpzqhwctrl, priv->mpzqhwctrl,
MPZQHWCTRL_ZQ_HW_FORCE);
/* 9a. calibrations now, wr lvl */
@@ -116,11 +116,11 @@ void mmdc_init(void)
out_be32(&mmdc->mppdcmpr2, MPPDCMPR2_MPR_COMPARE_EN);
/* set absolute read delay offset */
-#if defined(CONFIG_MMDC_MPRDDLCTL)
- out_be32(&mmdc->mprddlctl, CONFIG_MMDC_MPRDDLCTL);
-#else
- out_be32(&mmdc->mprddlctl, MMDC_MPRDDLCTL_DEFAULT_DELAY);
-#endif
+ if (priv->mprddlctl)
+ out_be32(&mmdc->mprddlctl, priv->mprddlctl);
+ else
+ out_be32(&mmdc->mprddlctl, MMDC_MPRDDLCTL_DEFAULT_DELAY);
+
set_wait_for_bits_clear(&mmdc->mpdgctrl0,
AUTO_RD_DQS_GATING_CALIBRATION_EN,
AUTO_RD_DQS_GATING_CALIBRATION_EN);
@@ -142,13 +142,13 @@ void mmdc_init(void)
CMD_BANK_ADDR_3);
/* 10. configure power-down, self-refresh entry, exit parameters */
- out_be32(&mmdc->mdpdc, CONFIG_MMDC_MDPDC);
+ out_be32(&mmdc->mdpdc, priv->mdpdc);
out_be32(&mmdc->mapsr, MMDC_MAPSR_PWR_SAV_CTRL_STAT);
/* 11. ZQ config again? do nothing here */
/* 12. refresh scheme */
- set_wait_for_bits_clear(&mmdc->mdref, CONFIG_MMDC_MDREF,
+ set_wait_for_bits_clear(&mmdc->mdref, priv->mdref,
MDREF_START_REFRESH);
/* 13. disable CON_REQ */
diff --git a/include/configs/ls1012afrdm.h b/include/configs/ls1012afrdm.h
index 136d648..612f243 100644
--- a/include/configs/ls1012afrdm.h
+++ b/include/configs/ls1012afrdm.h
@@ -20,22 +20,6 @@
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END 0x9fffffff
-/* DDR board-specific timing parameters */
-#define CONFIG_MMDC_MDCTL 0x04180000
-#define CONFIG_MMDC_MDPDC 0x00030035
-#define CONFIG_MMDC_MDOTC 0x12554000
-#define CONFIG_MMDC_MDCFG0 0xbabf7954
-#define CONFIG_MMDC_MDCFG1 0xdb328f64
-#define CONFIG_MMDC_MDCFG2 0x01ff00db
-#define CONFIG_MMDC_MDMISC 0x00001680
-#define CONFIG_MMDC_MDREF 0x0f3c8000
-#define CONFIG_MMDC_MDRWD 0x00002000
-#define CONFIG_MMDC_MDOR 0x00bf1023
-#define CONFIG_MMDC_MDASP 0x0000003f
-#define CONFIG_MMDC_MPODTCTRL 0x0000022a
-#define CONFIG_MMDC_MPZQHWCTRL 0xa1390003
-
-
/*
* USB
*/
diff --git a/include/configs/ls1012aqds.h b/include/configs/ls1012aqds.h
index b6d12dd..54abf30 100644
--- a/include/configs/ls1012aqds.h
+++ b/include/configs/ls1012aqds.h
@@ -19,22 +19,6 @@
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END 0x9fffffff
-/* DDR board-specific timing parameters */
-#define CONFIG_MMDC_MDCTL 0x05180000
-#define CONFIG_MMDC_MDPDC 0x00030035
-#define CONFIG_MMDC_MDOTC 0x12554000
-#define CONFIG_MMDC_MDCFG0 0xbabf7954
-#define CONFIG_MMDC_MDCFG1 0xdb328f64
-#define CONFIG_MMDC_MDCFG2 0x01ff00db
-#define CONFIG_MMDC_MDMISC 0x00001680
-#define CONFIG_MMDC_MDREF 0x0f3c8000
-#define CONFIG_MMDC_MDRWD 0x00002000
-#define CONFIG_MMDC_MDOR 0x00bf1023
-#define CONFIG_MMDC_MDASP 0x0000003f
-#define CONFIG_MMDC_MPODTCTRL 0x0000022a
-#define CONFIG_MMDC_MPZQHWCTRL 0xa1390003
-
-
/*
* QIXIS Definitions
*/
diff --git a/include/configs/ls1012ardb.h b/include/configs/ls1012ardb.h
index 2076ce5..0c13dde 100644
--- a/include/configs/ls1012ardb.h
+++ b/include/configs/ls1012ardb.h
@@ -19,21 +19,6 @@
#define CONFIG_SYS_MEMTEST_START 0x80000000
#define CONFIG_SYS_MEMTEST_END 0x9fffffff
-/* DDR board-specific timing parameters */
-#define CONFIG_MMDC_MDCTL 0x05180000
-#define CONFIG_MMDC_MDPDC 0x00030035
-#define CONFIG_MMDC_MDOTC 0x12554000
-#define CONFIG_MMDC_MDCFG0 0xbabf7954
-#define CONFIG_MMDC_MDCFG1 0xdb328f64
-#define CONFIG_MMDC_MDCFG2 0x01ff00db
-#define CONFIG_MMDC_MDMISC 0x00001680
-#define CONFIG_MMDC_MDREF 0x0f3c8000
-#define CONFIG_MMDC_MDRWD 0x00002000
-#define CONFIG_MMDC_MDOR 0x00bf1023
-#define CONFIG_MMDC_MDASP 0x0000003f
-#define CONFIG_MMDC_MPODTCTRL 0x0000022a
-#define CONFIG_MMDC_MPZQHWCTRL 0xa1390003
-
/*
* USB
*/
diff --git a/include/fsl_mmdc.h b/include/fsl_mmdc.h
index 1d09ff4..d5c4f8d 100644
--- a/include/fsl_mmdc.h
+++ b/include/fsl_mmdc.h
@@ -150,10 +150,23 @@ struct mmdc_regs {
u32 mpdccr;
};
-void mmdc_init(void);
+struct fsl_mmdc_info {
+ u32 mdctl;
+ u32 mdpdc;
+ u32 mdotc;
+ u32 mdcfg0;
+ u32 mdcfg1;
+ u32 mdcfg2;
+ u32 mdmisc;
+ u32 mdref;
+ u32 mdrwd;
+ u32 mdor;
+ u32 mdasp;
+ u32 mpodtctrl;
+ u32 mpzqhwctrl;
+ u32 mprddlctl;
+};
-#if !defined(CONFIG_MMDC_MDCTL)
-#error Must configure board-specific timing CONFIG_MMDC_* in <board>.h for MMDC
-#endif
+void mmdc_init(const struct fsl_mmdc_info *);
#endif /* FSL_MMDC_H */
--
2.7.4
_______________________________________________
U-Boot mailing list
U-Boot@lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
