Hi Marek, On Fri, Jul 21, 2017 at 8:36 PM, Marek Vasut <[email protected]> wrote: > On 07/21/2017 02:34 PM, Bin Meng wrote: >> Hi Marek, >> >> On Fri, Jul 21, 2017 at 6:06 PM, Marek Vasut <[email protected]> wrote: >>> On 07/21/2017 12:04 PM, Bin Meng wrote: >>>> Hi Marek, >>>> >>>> On Fri, Jul 21, 2017 at 4:56 PM, Marek Vasut <[email protected]> wrote: >>>>> On 07/21/2017 10:54 AM, Bin Meng wrote: >>>>>> Hi Marek, >>>>>> >>>>>> On Thu, Jul 20, 2017 at 8:20 PM, Marek Vasut <[email protected]> wrote: >>>>>>> On 07/20/2017 02:16 PM, Bin Meng wrote: >>>>>>>> Hi Marek, >>>>>>>> >>>>>>>> On Thu, Jul 20, 2017 at 7:12 AM, Bin Meng <[email protected]> wrote: >>>>>>>>> This series is the final series of the xHCI driver update. >>>>>>>>> >>>>>>>>> This adds the missing interrupt transfer support to xHCI driver, so >>>>>>>>> that devices like USB keyboard that uses interrupt transfer when >>>>>>>>> CONFIG_SYS_USB_EVENT_POLL is defined can work. >>>>>>>>> >>>>>>>>> This also adds full speed device support. Unlike low/high/super speed >>>>>>>>> devices, full speed device may report its endpoint 0 max packet size >>>>>>>>> as 8/16/32/64. xHCI driver guesses 64 for the first attempt to get the >>>>>>>>> initial 8 bytes device descriptor, and later adjusts the context for >>>>>>>>> endpoint 0. >>>>>>>>> >>>>>>>>> This series also made several updates to xHCI driver to conform with >>>>>>>>> the spec. >>>>>>>>> >>>>>>>>> Previous two series: >>>>>>>>> [1]: usb: xhci: Fix USB xHCI support on Intel platform >>>>>>>>> https://lists.denx.de/pipermail/u-boot/2017-June/296166.html >>>>>>>>> [2]: usb: hub: Support USB 3.0 hubs >>>>>>>>> https://lists.denx.de/pipermail/u-boot/2017-June/296284.html >>>>>>>>> >>>>>>>>> This series is available at u-boot-x86/xhci-working3 for testing. >>>>>>>>> >>>>>>>>> Changes in v3: >>>>>>>>> - rebase on u-boot-usb/master >>>>>>>>> - add changes to poplar.h >>>>>>>>> >>>>>>>>> Bin Meng (13): >>>>>>>>> usb: xhci: Add interrupt transfer support >>>>>>>>> usb: configs: Clean up CONFIG_SYS_USB_EVENT_POLL_(xxx) in board >>>>>>>>> configs >>>>>>>>> usb: kbd: kconfig: Set a default polling mechanism for USB keyboard >>>>>>>>> usb: Only get 64 bytes device descriptor for full speed devices >>>>>>>>> usb: Read device descriptor after device is addressed for xHCI >>>>>>>>> usb: xhci: Fix max packet size for full speed device endpoint 0 >>>>>>>>> usb: hub: Clear port reset before usb_hub_port_connect_change() >>>>>>>>> usb: hub: Clear BH reset status change for a 3.0 hub >>>>>>>>> usb: Handle audio extension endpoint descriptor in >>>>>>>>> usb_parse_config() >>>>>>>>> usb: xhci: Honor endpoint's interval >>>>>>>>> usb: xhci: Program max burst size for endpoint >>>>>>>>> usb: xhci: Set 'Error Count' to 0 for isoch endpoints >>>>>>>>> usb: xhci: Set 'Average TRB Length' to 8 for control endpoints >>>>>>>>> >>>>>>>> >>>>>>>> This is the last xHCI series I have. Can you please take a look and >>>>>>>> apply? >>>>>>> >>>>>>> I'd like to see some RB/TB from Stefan Roese first if possible. >>>>>>> >>>>>> >>>>>> OK, if that's the case, can you send a pull request to Tom to get usb >>>>>> in? So that I can apply Stefan's x86 patch series on top of this. (I >>>>>> cannot send PR for x86 before the usb changes) >>>>> >>>>> I actually cannot because the USB is currently broken, sorry, I'm >>>>> waiting for a fix before I do that. >>>>> >>>>> Stefan, can you look at this series please? >>>> >>>> What "broken" issues are you seeing? >>> >>> I think Layerscape stopped building. Look at email with this subject >>> "Compile failure encountered on latest (2017-07-20) >>> git://git.denx.de/u-boot-usb.git branch master for target >>> ls1021atwr_nor_defconfig" >> >> I see Patrice is working on a fix for the build failure. > > Correct, it's almost done. Sorry for the delay.
FYI, since it was reported by Ran this series has some issues on NXP LS1021ATWR, I will need allocate some time to figure out why. BTW: when will the u-boot-usb PR be sent? Not for any push, but Stefan's x86 patches are in the x86 repo which depends on contents on u-boot-usb and lots of Kconfig was changed in u-boot/master. The longer time our patches are staying off stream, the more chances we get rebase conflicts. Regards, Bin _______________________________________________ U-Boot mailing list [email protected] https://lists.denx.de/listinfo/u-boot
