Hi Tim, On Mon, Oct 3, 2022 at 3:22 PM Tim Harvey <[email protected]> wrote:
> With CONFIG_CMD_NET=y what does 'net list' show? > > I have the following (with network attached to lan4 port) > Net: MV88E61XX eth0: ethernet@2188000, eth1: lan4, eth2: lan3, eth3: lan2, > eth > 4: lan1 > Hit any key to stop autoboot: 0 > Ventana > print ethaddr > ethaddr=00:d0:12:f3:f2:f5 > Ventana > dm tree > ... > ethernet 0 [ + ] fecmxc | | |-- ethernet@2188000 > bootdev 0 [ ] eth_bootdev | | | |-- > [email protected] > mdio 0 [ + ] fec_mdio | | | `-- mdio > dsa 0 [ + ] mv88e6xxx | | | `-- switch@0 > ethernet 1 [ + ] dsa-port | | | |-- lan4 > bootdev 2 [ ] eth_bootdev | | | | > `-- switch@[email protected] > ethernet 2 [ + ] dsa-port | | | |-- lan3 > bootdev 3 [ ] eth_bootdev | | | | > `-- switch@[email protected] > ethernet 3 [ + ] dsa-port | | | |-- lan2 > bootdev 4 [ ] eth_bootdev | | | | > `-- switch@[email protected] > ethernet 4 [ + ] dsa-port | | | |-- lan1 > bootdev 5 [ ] eth_bootdev | | | | > `-- switch@[email protected] > mdio 1 [ + ] mv88e6xxx_mdio | | | > `-- mv88e6xxx-mdio-0 > ... > Ventana > net list > eth0 : ethernet@2188000 00:d0:12:f3:f2:f5 active > eth1 : lan4 00:d0:12:f3:f2:f5 > eth2 : lan3 00:d0:12:f3:f2:f5 > eth3 : lan2 00:d0:12:f3:f2:f5 > eth4 : lan1 00:d0:12:f3:f2:f5 > Ventana > setenv ethact lan4 > Ventana > dhcp > BOOTP broadcast 1 > BOOTP broadcast 2 > BOOTP broadcast 3 > DHCP client bound to address 172.24.33.142 (1076 ms) > > I do not use CONFIG_NET_RANDOM_ETHADDR and have a single MAC address > allocated to the board. Below are the logs: Net: MV88E61XX Warning: ethernet@30be0000 (eth0) using random MAC address - a6:a6:56:1c:28:0a eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Your log also shows eth1-eth4. Mine does not. Unlike your log, dsa-port is not getting probed here: ethernet 0 [ + ] fecmxc | | `-- ethernet@30be0000 bootdev 2 [ ] eth_bootdev | | |-- [email protected] mdio 0 [ + ] fec_mdio | | `-- mdio dsa 0 [ ] mv88e6xxx | | `-- switch@0 ethernet 1 [ ] dsa-port | | |-- lan4 bootdev 3 [ ] eth_bootdev | | | `-- switch@[email protected] ethernet 2 [ ] dsa-port | | |-- lan3 bootdev 4 [ ] eth_bootdev | | | `-- switch@[email protected] ethernet 3 [ ] dsa-port | | |-- lan2 bootdev 5 [ ] eth_bootdev | | | `-- switch@[email protected] ethernet 4 [ ] dsa-port | | |-- lan1 bootdev 6 [ ] eth_bootdev | | | `-- switch@[email protected] mdio 1 [ + ] mv88e6xxx_mdio | | |-- mv88e6xxx-mdio-0 mdio 2 [ ] mv88e6xxx_mdio | | |-- mv88e6xxx-mdio-1 mdio 3 [ ] mv88e6xxx_mdio | | |-- mv88e6xxx-mdio-2 mdio 4 [ ] mv88e6xxx_mdio | | `-- mv88e6xxx-mdio-3 simple_bus 7 [ ] simple_bus | `-- bus@32c00000 usb 0 [ ] ehci_mx6 | `-- usb@32e40000 phy 0 [ ] nop_phy |-- usbphynop1 regulator 0 [ ] regulator_fixed |-- regulator-usdhc2 sysreset 1 [ ] wdt_reboot |-- wdt-reboot bootstd 0 [ ] bootstd_drv `-- bootstd bootmeth 0 [ ] bootmeth_distro |-- distro bootmeth 1 [ ] bootmeth_efi |-- efi bootmeth 2 [ ] bootmeth_pxe |-- pxe bootmeth 3 [ ] vbe_simple `-- vbe_simple u-boot=> net list eth0 : ethernet@30be0000 a6:a6:56:1c:28:0a active eth1 : lan4 00:00:00:00:00:00 eth2 : lan3 00:00:00:00:00:00 eth3 : lan2 00:00:00:00:00:00 eth4 : lan1 00:00:00:00:00:00 u-boot=> setenv ethact lan4 u-boot=> dhcp BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 BOOTP broadcast 5 BOOTP broadcast 6 BOOTP broadcast 7 BOOTP broadcast 8 (IP is never retrieved) > What board are you using and what does its fec/mdio dt look like? I am using a custom imx8mn board. The FEC/MDIO nodes are like this: https://pastebin.com/raw/0SvLLzxj Thanks, Fabio Estevam
