Enrich README.fsl-hwconfig with this sd1 reconfiguration scenarios. Add a reference to the Layerscape README.soc.
Signed-off-by: Vincent Jardin <[email protected]> --- Changes in v6: - Only 161.1328125 MHz PLLS reference clock is supported, from the PLLS input or through SRDS_INTRA_REF_CLK_S1 (Vladimir) Changes in v5: - Reword the grouping sentence, suggested by Vladimir - PLLS reference clock as an initial condition - Drop the MC bullet, and the list of boards Changes in v4: - was v3 5/5, rewritten using a table .../cpu/armv8/fsl-layerscape/doc/README.soc | 7 ++ doc/README.fsl-hwconfig | 64 +++++++++++++++++++ 2 files changed, 71 insertions(+) diff --git a/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc b/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc index f2efd4cc1d7..a641e4978aa 100644 --- a/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc +++ b/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc @@ -331,6 +331,13 @@ LX2160A SoC has 2 more similar SoC personalities 2)LX2080A, few difference w.r.t. LX2160A: a) Eight 64-bit ARM v8 Cortex-A72 CPUs +SerDes 1 lane grouping + SRDS_PRTCL_S1 is latched at reset. U-Boot can still configure SD1 before + the MC starts: + 1x100GE + 4x25G, 2x40GE, 1x40GE + 4x10G or 1x100GE + 4x10G. + See 'serdes1' in doc/README.fsl-hwconfig, and the 'lx2160_serdes status' + command. + LS1028A -------- diff --git a/doc/README.fsl-hwconfig b/doc/README.fsl-hwconfig index e752505da49..91bc39d7238 100644 --- a/doc/README.fsl-hwconfig +++ b/doc/README.fsl-hwconfig @@ -44,3 +44,67 @@ usb usb1:dr_mode=host;usb2:dr_mode=peripheral' usb1:dr_mode=host,phy_type=utmi;usb2:dr_mode=host' + +serdes1 + Specific to the LX2160A boards whose reset_phy() calls + lx2160a_serdes_apply_hwconfig() before mc_env_boot(). + + SRDS_PRTCL_S1 is latched at reset, but the eight SD1 (SerDes) lanes + can still be configured before the DPAA2 management complex (MC) starts. + This option alters the Ethernet MAC-to-lane grouping after the fact + (RCWSR29 keeps reporting the initial protocol). + + 'serdes1:2x100g' + 2x 100GE (CAUI-4), what protocol 13 builds: nothing to do + + 'serdes1:100g4x25g' + 1x 100GE + 4x 25G + + 'serdes1:2x40g' + 2x 40GE (XLAUI-4) + + 'serdes1:40g4x10g' + 1x 40GE + 4x 10G (XFI) + + 'serdes1:100g4x10g' + 1x 100GE + 4x 10G (XFI) + + Each mode starts from the one in the 'from' column, which is + entered first when SD1 is not in it yet, and so on down to what + SRDS_PRTCL_S1 built: + + mode from SRDS_PRTCL_S1 lanes run on + 2x100g - 13 PLLF + 100g4x25g 2x100g 13 PLLF + 2x40g 2x100g 13 PLLS + 40g4x10g 2x40g 13 or 20 PLLS + 100g4x10g 2x100g 13 PLLF and PLLS + + What each mode makes of the two four-lane ports of protocol 13: + + mode dpmac.2 port dpmac.1 port + 2x100g 100GE 100GE + 100g4x25g 100GE 4x 25G: dpmac.3 to dpmac.6 + 2x40g 40GE 40GE + 40g4x10g 40GE 4x XFI: dpmac.3 to dpmac.6 + 100g4x10g 100GE 4x XFI: dpmac.3 to dpmac.6 + + Initial conditions: + + - PLLS needs a 161.1328125 MHz reference clock, for which 2x40g, + 40g4x10g and 100g4x10g program it. It can come from the SD1 + PLLS reference clock input, or from the PLLF one with + SRDS_INTRA_REF_CLK_S1=1. A 156.25 MHz PLLS reference clock is + not supported. With protocol 13 PLLS is not in use, so nothing + checks that clock before these modes start it. + - The MC DPC must set follow_hw_pssr in board_info/serdes, for the + MC to read the lanes rather than look at protocol, and the DPL + must use the dpmacs of the new grouping. + + 'lx2160_serdes status 1' shows the resulting lane grouping and + protocol converters. + + Example: + setenv hwconfig serdes1:100g4x25g + saveenv + reset -- 2.43.0
