I just upgraded a pair of Rockets to 5.5.10 and was able to enable DFS. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Dec 7, 2014 8:11 PM, "Jason Bailey" <j284...@yahoo.com> wrote:
> Going back to 5.5.8 and clicking the uni-2 box on the system page will get > you there. > > > On Sunday, December 7, 2014 8:08 PM, Kees H <wi...@calbroadband.com> > wrote: > > > You have to downgrade the software ( I think it was 5.5.4 that had the > DFS key) then enter the dfs key and then upgrade. > > ----- Original Message ----- > *From:* Mike Hammett <wispaubntus...@ics-il.net> > *To:* Ubiquiti Users Group <ubnt_users@wispa.org> > *Sent:* Sunday, December 07, 2014 11:00 AM > *Subject:* Re: [Ubnt_users] Old Rockets, weird problems > > I believe that has been done. > > Definitely the reboot both sides. > > The DFS checkbox\fields are definitely not there. > > > > ----- > Mike Hammett > Intelligent Computing Solutions > http://www.ics-il.com > > ------------------------------ > *From: *"Josh Luthman" <j...@imaginenetworksllc.com> > *To: *"Ubiquiti Users Group" <ubnt_users@wispa.org> > *Sent: *Sunday, December 7, 2014 12:47:46 PM > *Subject: *Re: [Ubnt_users] Old Rockets, weird problems > > Old rocket, plug in DFS credentials for your company, reboot BOTH SIDES. > BOTH. > Josh Luthman > Office: 937-552-2340 > Direct: 937-552-2343 > 1100 Wayne St > Suite 1337 > Troy, OH 45373 > On Dec 7, 2014 1:45 PM, "Mike Hammett" <wispaubntus...@ics-il.net> wrote: > > I have some old Rockets (maybe 5.2.1 vintage?). I upgraded them as > needed throughout the years. The past day or two, performance in on part of > the network has been erratic to say the best of it. > > I noticed that they were in Compliance Test mode, but didn't have the > input boxes for the DFS stuff, so I must have entered it at one point, but > never actually moved over. They were on 5.5.2. > > Don't fuck with what works. Well, now it's not working right. > > I upgrade to 5.5.4, then 5.5.10. I set the country code to US.... no DFS > channels show up on the AP. > > Do I need to reboot it after setting it to US so that I can get the DFS > channels? > > A reset to defaults and starting over is kinda out of the question at the > moment. > > Any other ideas? > > If I have to climb to replace radios, ePMPs are going up instead. > > > > > > ----- > Mike Hammett > Intelligent Computing Solutions > http://www.ics-il.com > > _______________________________________________ > Ubnt_users mailing list > Ubnt_users@wispa.org > http://lists.wispa.org/mailman/listinfo/ubnt_users > > > _______________________________________________ > Ubnt_users mailing list > Ubnt_users@wispa.org > http://lists.wispa.org/mailman/listinfo/ubnt_users > > ------------------------------ > _______________________________________________ > Ubnt_users mailing list > Ubnt_users@wispa.org > http://lists.wispa.org/mailman/listinfo/ubnt_users > > > _______________________________________________ > Ubnt_users mailing list > Ubnt_users@wispa.org > http://lists.wispa.org/mailman/listinfo/ubnt_users > > > > _______________________________________________ > Ubnt_users mailing list > Ubnt_users@wispa.org > http://lists.wispa.org/mailman/listinfo/ubnt_users > >
_______________________________________________ Ubnt_users mailing list Ubnt_users@wispa.org http://lists.wispa.org/mailman/listinfo/ubnt_users
