For clarification - the 2nd upgrade doesn't automaticallyenable dfs support, youstill have to add that first. What the 2nd upgrade to the same firmware fixes is the 5150-5250 not showing up.

josh reynolds :: chief information officer
spitwspots :: www.spitwspots.com

On 12/08/2014 07:22 AM, Josh Reynolds wrote:
I've found that when you upgrade a device to 5.5.10, you'll often have to upgrade it to 5.5.10 twice. Simply reloading 5.5.10 and upgrading fixes it.
josh reynolds :: chief information officer
spitwspots ::www.spitwspots.com
On 12/08/2014 07:17 AM, Kees H wrote:
You must have already DFS enabled in that rocket. Mike is talking about an older rocket before DFS was approved on the rockets. I ran into the same issue trying to use the 5240. I upgraded directly to 5.5.10 and no DFS nor 5160-5240 was avalable. I downgraded checked the uni box entered my codes and voila when I upgraded to 5.5.10 there was the 5160-5240. (eventhought those are not DFS :-)

    ----- Original Message -----
    *From:* Josh Luthman <mailto:[email protected]>
    *To:* Ubiquiti Users Group <mailto:[email protected]>
    *Sent:* Sunday, December 07, 2014 5:17 PM
    *Subject:* Re: [Ubnt_users] Old Rockets, weird problems

    I just upgraded a pair of Rockets to 5.5.10 and was able to
    enable DFS.

    Josh Luthman
    Office: 937-552-2340
    Direct: 937-552-2343
    1100 Wayne St
    Suite 1337
    Troy, OH 45373

    On Dec 7, 2014 8:11 PM, "Jason Bailey" <[email protected]
    <mailto:[email protected]>> wrote:

        Going back to 5.5.8 and clicking the uni-2 box on the system
        page will get you there.


        On Sunday, December 7, 2014 8:08 PM, Kees H
        <[email protected] <mailto:[email protected]>> wrote:


        You have to downgrade the software ( I think it was 5.5.4
        that had the DFS key) then enter the dfs key and then upgrade.

            ----- Original Message -----
            *From:* Mike Hammett <mailto:[email protected]>
            *To:* Ubiquiti Users Group <mailto:[email protected]>
            *Sent:* Sunday, December 07, 2014 11:00 AM
            *Subject:* Re: [Ubnt_users] Old Rockets, weird problems

            I believe that has been done.

            Definitely the reboot both sides.

            The DFS checkbox\fields are definitely not there.



            -----
            Mike Hammett
            Intelligent Computing Solutions
            http://www.ics-il.com <http://www.ics-il.com/>

            
------------------------------------------------------------------------
            *From: *"Josh Luthman" <[email protected]
            <mailto:[email protected]>>
            *To: *"Ubiquiti Users Group" <[email protected]
            <mailto:[email protected]>>
            *Sent: *Sunday, December 7, 2014 12:47:46 PM
            *Subject: *Re: [Ubnt_users] Old Rockets, weird problems

            Old rocket, plug in DFS credentials for your company,
            reboot BOTH SIDES.  BOTH.
            Josh Luthman
            Office: 937-552-2340 <tel:937-552-2340>
            Direct: 937-552-2343 <tel:937-552-2343>
            1100 Wayne St
            Suite 1337
            Troy, OH 45373
            On Dec 7, 2014 1:45 PM, "Mike Hammett"
            <[email protected]
            <mailto:[email protected]>> wrote:

                I have some old Rockets (maybe 5.2.1 vintage?). I
                upgraded them as needed throughout the years. The
                past day or two, performance in on part of the
                network has been erratic to say the best of it.

                I noticed that they were in Compliance Test mode, but
                didn't have the input boxes for the DFS stuff, so I
                must have entered it at one point, but never actually
                moved over. They were on 5.5.2.

                Don't fuck with what works. Well, now it's not
                working right.

                I upgrade to 5.5.4, then 5.5.10. I set the country
                code to US....  no DFS channels show up on the AP.

                Do I need to reboot it after setting it to US so that
                I can get the DFS channels?

                A reset to defaults and starting over is kinda out of
                the question at the moment.

                Any other ideas?

                If I have to climb to replace radios, ePMPs are going
                up instead.





                -----
                Mike Hammett
                Intelligent Computing Solutions
                http://www.ics-il.com <http://www.ics-il.com/>

                _______________________________________________
                Ubnt_users mailing list
                [email protected] <mailto:[email protected]>
                http://lists.wispa.org/mailman/listinfo/ubnt_users


            _______________________________________________
            Ubnt_users mailing list
            [email protected] <mailto:[email protected]>
            http://lists.wispa.org/mailman/listinfo/ubnt_users

            
------------------------------------------------------------------------
            _______________________________________________
            Ubnt_users mailing list
            [email protected] <mailto:[email protected]>
            http://lists.wispa.org/mailman/listinfo/ubnt_users


        _______________________________________________
        Ubnt_users mailing list
        [email protected] <mailto:[email protected]>
        http://lists.wispa.org/mailman/listinfo/ubnt_users



        _______________________________________________
        Ubnt_users mailing list
        [email protected] <mailto:[email protected]>
        http://lists.wispa.org/mailman/listinfo/ubnt_users

    ------------------------------------------------------------------------
    _______________________________________________
    Ubnt_users mailing list
    [email protected]
    http://lists.wispa.org/mailman/listinfo/ubnt_users



_______________________________________________
Ubnt_users mailing list
[email protected]
http://lists.wispa.org/mailman/listinfo/ubnt_users



_______________________________________________
Ubnt_users mailing list
[email protected]
http://lists.wispa.org/mailman/listinfo/ubnt_users

_______________________________________________
Ubnt_users mailing list
[email protected]
http://lists.wispa.org/mailman/listinfo/ubnt_users

Reply via email to